Other parts of the country may be warming up and getting ready to use our air conditioners, but we’re still relying on our heaters to get us through more than a few chilly nights. So if yours begins to malfunction, you may start to panic. This is understandable, but know that if you’ve had your system maintained before the heating season began, it may likely not even be an issue with the system itself.

Instead, you may be in need of Newton, MA electrical wiring services for some component of your heater. Keep reading to learn more about how your heater can be impacted by electrical issues.

This applies to both electrical furnaces as well as boilers. Both of these systems use heating elements—a set of coils that burn hot as a current passes through them—in order to raise the temperature of the air (furnaces) or water (boilers).

Both of these systems contain more than one heating element. Therefore, if you one fails you likely won’t lose your heat entirely, but your heater won’t be able to work as efficiently as it otherwise would.

If you’re utilizing a heat pump, then this is the most common electrical problem you might run into. Capacitors are cylindrical devices about the size of a soda can, responsible for sending electrical charges to the motors to start and keep them running.

Capacitors can burn out after years of use, or suffer from wiring issues, causing the heat pump to “hard start” (draining power) or quit functioning all together. You’ll need a professional to replace the damaged electrical capacitors.

Even if you have a heater that runs off of natural gas, oil, propane, or geothermal power, it’s going to have an electrical thermostat controlling it. Thermostats with failing wiring will begin to malfunction, often incorrectly registering your home’s temperature or failing to accurately set the heater. If your heater is failing to reach its target temperature with no other signs of a problem, your thermostat wiring could certainly be to blame.

We’ve touched a bit on the subject of Do It Yourself solutions in the past. Mostly making mention here or there of when it is, and is not, a good idea. But at Kolb Electric, your safety is always our absolute primary goal. So rather than leave it at a mention, we wanted to take some time to tell you some important points. 

We support all kinds of on-your-own projects. It’s a great way to get a new skill set, or polish one you already have. Plus, nothing beats that feeling of accomplishment you get from creating or building something all on your own. But when it comes to DIY electrical work, we would firmly call it a really bad idea.

It really comes down to one major point: harm. It is entirely too easy to cause harm to yourself, to others, or to your personal property. If you follow along with our blog, you may remember a point we made in the article about “What It Takes To Become An Electrician”. In that post, we mentioned that anyone pursuing an education in electrical work pay very close attention to the safety aspects of learning.

This is because electricity, by nature, is highly volatile, and can be hard to predict without training. It only takes one, single misstep and suddenly you, or your home, is on fire. There are plenty of articles out there on how to wire an outlet, or replace a ceiling fan, but please be aware that 1) these articles are rarely comprehensive and 2) reading something and doing it are two very different things.

The U.S. Consumer Product Safety Commission has stated that roughly 400 domestic electrocutions occur every year. And of the estimated 360,900 residential building fires reported, the leading cause is electrical issues and mistakes. We really want to nail home the point that this kind of work takes training and experience to work well. Without these two things, you risk:

Fires that result in catastrophic property loss can even be caused by incorrect bulb wattage, so please keep in mind that something as intense as rewiring should be handled by a trained and certified professional.

Next time you need electrical work, trust in the certified professionals at Kolb to get the job done right! Don’t risk yourself, and your investments on a personal side project. Contact certified electricians today to learn more about our comprehensive electrical services.

One of the best things you can do to protect your home and keep your family safe is to add motion sensor installation to your Fairfax, VA property. Simply put, when someone is close enough to your home, their motion is detected and a light comes on. This bright light deters intruders, alerts neighbors and makes you aware of what’s taking place on the perimeter of your house.

Bright lights are an intruders worst nightmare. Thieves and home invaders thrive on the hidden cover of darkness. Motion sensors also protect your home when you’re away. You’ll feel more secure knowing anyone approaching your home will be seen by neighbors and passersby.

The most common places to install motion sensors are in close proximity to garage doors, porches or patios, backyards and front and back entry doors. A quality motion sensor also helps illuminate your walkways as you approach your home after dark.

Motion sensors can even help decrease your electricity bills. Because motion sensors only come on when movement is detected, they are less costly than porch and other exterior lights that must run continually. No more hunting around for light switches in the dark, either.

There’s a lot more to the cost of a light bulb than the price tag sticker. There’s the impact on your electrical bill, the tally of replacement bulbs you’ll need to buy, and the time you have to factor in for maintenance. Sure, the light bulb in your table lamp may take just a few minutes to replace, but what about your recessed cans that are two stories away from easy access?

We published an infographic on Lighting Facts, a program of the U.S. Department of Energy, created the one below, showing the five-year-cost of 100 watt equivalent light bulbs. As you can see, the low purchase cost of an incandescent light bulb doesn’t necessarily pay off in the end: