Whole-home surge protectors are designed to protect your home from dangerous lightning strikes that could knock out power or fry your electronics, potentially resulting in thousands of dollars in damages.  Recently, however, there has been a lot of controversy surrounding whole-home surge protectors, claiming they’re a waste of money and don’t do what they claim to be able to do. So what’s the real story here? Are whole home surge protectors worth it?

We’ll start by talking about what surge protectors are not designed for: protecting your home from all sources of increased voltage. Power surges most commonly originate inside your home as a result of different appliances turning on and off. Depending on your home’s electrical service (100amp vs 200amp or whatever you may have), you’ve probably seen this in the form of flickering lights when your air conditioner cycles on.

Whole-home surge protectors do protect your home from power surges that originate outside, commonly caused by lightning strikes but also resulting from any interruptions to the power: downed wires or utility poles, wind damage, utility repairs, etc.

There are a few different ways power surges can occur. Lightning strikes, which people tend to be most worried about, are actually pretty uncommon—conditions need to be perfect, and the strike needs to occur less than one mile away from your home. Despite their rarity, lightning strikes can send a 200,000-amp jolt through your home and are definitely not to be taken lightly.

The majority of external power surges occur when the magnetic field created by wires conducting electricity collapses, which sends large voltages down the wires and eventually, into homes and buildings.

Effectively defending your home from power surges requires a two-step approach: first, outfitting it with a whole-home surge protector, then using surge-protected outlets and power strips indoors. Both types of surge protectors act essentially like pressure relief valves, diverting excess energy away and restoring normal operation once levels regulate.

Whole-home surge protectors are usually wired to a service panel and are designed to stop surges of at least 40,000 amps, though larger ones can be installed. Pairing them with individual plug-in surge protectors should do a good job of catching any potentially damaging energy that may get into your home.

Like many safety-related things, whole-home surge protectors are appliances you buy and hope to never actually use. But all it takes is a single downed line or big lightning strike to cause thousands of dollars’ worth of damage to your home—not worth the risk!

If you want to protect your home from dangerous jolts of electricity by installing a whole-home surge protector, call Kolb Electric today!

Cleaning a crystal chandelier isn’t as daunting as it may appear. These precious fixtures require a little more love and care than a desk lamp, but you can restore and maintain your crystal’s shine with common household products and a little know-how.

Everyday Care

If your chandelier is still sparkling clean, simply dust the fixture with a lambswool or feather duster every few weeks. Keep your strokes light, since leaded crystal is softer than glass—even dust can scratch it. Be sure to walk around the fixture as you dust, rather than spinning it towards you. Twisting the fixture can strain the wiring or loosen its support.

Spring Cleaning

Eventually, the fixture will need a more thorough cleaning, especially if it’s in a high-traffic area or kitchen. Mid-size chandeliers are still manageable at this stage, provided you have some clean, lint-free rags, isopropyl alcohol, and a little elbow grease.

Before touching the chandelier, follow rule number one: turn off the power to the room when dealing with a ceiling fixture. At least flip the light switch off and tape it so no one will accidentally turn the light on while you’re working. Set up an alternative light source to aid the cleaning. Once the chandelier bulbs have cooled, cover them with plastic snack bags and secure with a rubber band.

Fill a spray bottle with one part isopropyl alcohol and three parts distilled water. Spray on one section of the chandelier at a time, then wipe off with a white cotton glove or lint-free cloth, making sure you dry the frame as well as the crystal. This solution will clarify the crystal and help remove the haze, but is gentler than ammonia on crystal with a design or edge finish. Even so, gently wipe away after spraying and don’t allow the fixture to drip dry. This will help preserve the frame.

Try cleaning your chandelier every two to six months with the alcohol solution, depending on whether the fixture is in a high-traffic area or not.

Heavy Restoration

If your fixture hasn’t been cleaned in a long time (or just needs extra attention), you can go an extra step before calling a professional. This is where a digital camera comes in handy, as you’ll need to remove individual pendants for a more thorough washing. Take pictures of the connections for reference later, then carefully remove the pendants. You may need a pair of needle-nose pliers to help disengage the pendants from the fixture.

Fill a sink with warm water and some gentle dish soap. Carefully wash each crystal piece and rinse in warm water to avoid any drastic temperature shifts. Set the pendants on a clean cloth to dry. Then simply rehang the pendants and enjoy your sparkling fixture!

We may be entering February, but if last year taught us anything, it’s that winter can throw us a few curve balls, even when the end of the season ought to be in sight. There is plenty more cold weather ahead of us, and likely some more snowfall to go with it. You need to know that your heating system in Boston, MA is not only to heat your home effectively, but also that it will do so efficiently. You don’t want to wait around in discomfort while you look forward to the start of spring, after all. That’s why we’ve put together a few tips to help you enjoy efficient heating in your home.

There are a lot of beautiful old homes in this part of the country. Of course, homes of this age were likely not constructed with the same attention paid to energy efficiency as newer ones are. Simply investing in some weather stripping with which to eliminate drafts in door and window frames can seriously help you to boost energy efficiency in your home. You may also want to consider wrapping your windows with plastic sealing, available at just about any hardware store, in order to help prevent drafts.

You may not realize just how huge of an impact your thermostat can have on the overall performance quality and efficiency of your HVAC system. Simply upgrading an old, outdated thermostat to a programmable model, for instance, means that you can come home to comfort every day, without maintaining that temperature in your house while it is empty for hours at a time. Program it to cater to your own personal schedule, and enjoy great comfort with increased efficiency.

Never convince yourself that you can skip over an annual heating maintenance service. Even if you didn’t have your system serviced going into winter, you should have it maintained at the close of the season. The time of the year doesn’t matter so much as the fact that it is serviced at least once a year. It’s not too late to ensure the success and efficiency of your heater with routine maintenance.

Tube lights are found in many applications and environments such as office buildings, hallways, garages, and really anywhere that has a low and flat ceiling. Although fluorescent tubes contain small amounts of mercury and isn’t a whole lot, you still want to avoid the breaking of a fluorescent tube and any exposure to mercury if possible.

Whether you are simply replacing a burnt out fluorescent tube with a new one or are switching over to a new technology (such as LED), there is a proper way to do it. By following these steps along with others that you may find, you will allow yourself to reduce risk of harm for yourself, staff, or whoever is the one physically replacing the tube lights.

Let’s answer some common questions and issues that people seem to face when tasked with this issue of replacing mercury filled fluorescent tubes…

By recycling rather than simply throwing away your tube lights, you opt-in for the environmentally friendly route of switching out old tubes. If you choose not to recycle, you are allowing toxic mercury to freely enter the environment, which of course is not good.

Not only do you prevent mercury from freely entering the environment by recycling, but you also reduce waste. How exactly? Part of the tube is reused for new tubes that will be resold and used. This allows for less waste and this goes back to the saying “Reduce, Reused, Recycle.” So by taking part of fluorescent tube recycling, you allow the process of recycling to continue and prevent waste from entering the landfill!

When taking your tubes out to bring for recycling, this is probably the most difficult step you need to be most cautious with. The best option you have is to be prepared and know what to do if things go “south” as they like to say.

Here is what you can do to prepare for the removal of fluorescent fixtures:

And for one thing that you should always remember for dealing with a broken tube is this: NEVER VACUUM. By vacuuming, you make glass particles go airborne and that is a highly dangerous situation to be in.

For more tips on how to clean up a broken fluorescent or CFL lights, using this tool from Earth911. It allows you to search what you need to recycle and where you are located. So you go to that tool, type in ‘fluorescent’ or ‘CFL’ along with your location and you will surely come across the closest place to recycle fluorescent tubes (along with really anything else you may want to recycle).

If you are in the process of disposing and recycling your fluorescent tubes, what is going in there to replace the ones you are removing? If the answer is “more fluorescent tubes,” may we ask why?