By Clarissa Allison | January 13th, 2017

Homeowners have always wanted to bring another time to life. Many of us want our homes to feel like a peaceful getaway echoing a country retreat, or to act as a transport to a different (note: picturesque) period of time. Unlike many design trends, the New Farmhouse style marries both of these desires and blends them smoothly. New Farmhouse doesn’t boast the same masculinity as straightforward Neo-Industrial nor is it a predictably dated Shabby Chic look, although some elements can cross-over. Finding the right items to achieve this scheme can be confusing, so we’ve compiled a few recommendations for the ideal lighting fixtures to complement your new design project.

The Kitchen

By Lindsay Mirick

When lightning strikes and thunder rolls, will you be prepared for the power surges that follow? When you think about storm proofing your home, power surge protection may not be the first thing that comes to mind. However, getting caught in a power surge during a storm without protection could leave you with some very expensive, very useless electronics. Mr. Electric has reasons why...

Many homeowners have the idea that surge protection is simply a matter of plugging their devices into a low-cost, multi-outlet surge suppressor. However, we all know that the cheapest option isn’t always the best option, and making exceptions can lead to more expensive consequences in the long run.

If you think about it, adding surge protection to your home costs very little in comparison to the replacement of your electronics. A single surge can follow any wire into a house and threaten televisions, computers, appliances, satellite systems, phone and cable lines, and any other electrical devices you can think of.

The cost of replacing a single large home appliance such as a washer or dryer will likely cost you double the investment of a whole house surge protector. According to the Insurance Information Institute, insurers paid over $673 million in lightning claims in 2013 alone. In the three years prior, approximately $1 billion was paid annually to policyholders.

Most people associate power surges with lighting strikes. However, many things both outside and inside the home can cause them. Outside the home, events such as power outages and power transitions in large equipment on the same power line can introduce damaging power surges on your electric lines. Inside the home reengaging trip circuit breakers or switching of pool pumps, AC units, and other devices with large motors can also introduce power surges onto your electric wiring. To effectively protect your home from these damaging surges, you need to implement whole house surge protection .

Ask yourself if can you afford to live without surge protection. A few hundred dollars isn’t much when you compare it to the cost of replacing some of your most cherished possessions, not to mention the inconvenience of living without them until they can be replaced.

Trust us to keep your valuables safe and let us power your tomorrow. Call Mr. Electric today!

Regardless of bends, twists, or turns, Example of a cut line on LED strip lights

2. You will now have two LED strip lights. Carefully peel back the end portion of the paper strip covering the strip’s adhesive backing, and then remove the 3M VHB adhesive from the solder pads on the bottom side of one of the strips. The strip with its adhesive peeled back will be the top strip when soldered.

5. Align the non-tinned strip segment (strip with adhesive removed) directly over the newly tinned pads, and apply heat. Hold the soldering iron in place until the solder remelts and begins to flow. To strengthen the bond and improve visual appeal, a small portion of solder can be added to the top pad.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split and solder a run of non-weatherproof two-conductor or connecting wires. Peel away the blue wire so that only the positive (red), negative (black), and control (green) wires are left.

*No wires should be peeled away if you’re joining single-color or standard RGB light strips.

3. Properly heat your soldering iron. For best results, clean and tin the tip of the iron immediately before soldering. To tin the iron, touch solder to both sides of the iron’s tip.

4. Next you will need to tin the solder pads on both ends of the split strip light. When soldering, always apply heat to the target area on the strip and not directly to the solder. Once sufficient heat has been applied to the area, start introducing solder.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split, solder, and reseal a

3. Follow steps two through five located at the top of this post for soldering a standard RGB strip light.

4. To reseal the strip light, apply

The LED strip lights are now connected, and power should flow through the entire length of the weatherproof strip.

Many homeowners know the pride and satisfaction that results from completing DIY repairs and improvements. But when it comes to electrical work, the stakes of making a rookie mistake can be high.

There are several common electrical projects that aren’t complicated or extensive, but even the simplest jobs can result in serious injury or property damage if they’re performed improperly. Before making any plans to engage in a DIY electrical project, it’s important to know the risks.

What Can Go Wrong

Electricians undergo an enormous amount of training in order to earn the licenses and certifications they need to do their work. That’s because mistakes could not only be dangerous for them, but also for anyone in the homes or buildings they’re working on. Even if you know your way around the circuit box, here’s what an electrical mishap can bring:

Hiring Electricians Saves Money

One of the most common reasons why electrical novices attempt this sort of work is to save money. But that plan can easily backfire even if no one gets hurt in the process.

Poorly performed electrical work can spark destructive fires. It can also fry circuits, destroy fixtures and even damage major appliances. When things go wrong, the cost of repairs is usually several times what it would cost to hire an electrician in the first place.

Making matters much worse, homeowners insurance companies will typically ask for confirmation that electrical work was performed by a licensed electrician before covering any damage from a related event. If your insurance carrier learns that you did the work on your own to save a few dollars, you could lose your claim or even invalidate your policy. Be sure you understand your full policy details before engaging in DIY work.

Know the Code?

When you hire an electrician, you’re not just passing the risk along to a professional -- you’re hiring someone who has knowledge you don't even realize your lacking.

Electrical work is constantly getting safer and more reliable through updates to the electrical code. Licensed electricians are required to keep up with this code as it evolves, so when you work with a professional, you can count on receiving the safest electrical work possible. When you go it alone, you may follow outdated methods because you weren’t aware of the code update.

Don’t take a chance. Your life and home are too valuable. When you need electrical work performed safely and properly, call upon your knowledgeable, licensed, local electricians.