Aluminum LED profile housings allow you to create customized light fixtures with LED strip lights. Our Klus brand LED channels are available in many different styles, including recessed-, or flexible, O-shaped, and more. Available in 1- and 2-meter lengths, the channels can be easily cut for any application from under-cabinet lighting and bookshelf lighting to showcase lighting and transition strip lighting. They’re available with a variety of lens options, such as clear, frosted, and etched that complete the profiles. We’ve put together a step-by-step guide for using these channels to create your own light fixtures. Please note that your specific channel might vary from the one used in this tutorial.

Materials needed:

1. With a pair of clippers, carefully clip through the clear plastic heat shrink as shown in figures A-C. You will want to take your time and be careful not to cut the strip’s wires while removing it.

2. Lay the LED strip into the channel, and position it along the bottom so that the ends of the strip and the channel are lined up (fig. A). Now, remove the paper from the strip’s adhesive backing (fig. B), and adhere the strip to the LED channel—starting at the lined end and working your way to the other end of the strip. Be sure to leave roughly 1/4-inch free at the end of the channel so that you can install the end cap as shown in figure C.

3. If one of your end caps doesn’t come with a pre-drilled hole, you will need to drill your own to allow the wires of the LED strip light to come through. In this case, we used a Dremel tool, but other options are viable as well. Regardless of the tool you choose, it is helpful to mark the end cap where you would like the wires to come through. Start the hole small, and increase the size as necessary.

4. Place the end cap on the wired side of the strip by threading the wires through the end cap as shown in figure A. Insert the end cap into the end of the light bar, and push firmly until it is fully in place (fig. B).

5. On the open end of the bar, slightly peel up the end of the LED strip (fig. A); this is necessary to install the end cap. Now measure your channel lens, and trim off the excess with clippers (fig. B). Be careful when trimming to avoid cracking the plastic. Excess material can be lightly sanded off. Once the lens has been cut to the proper length, slide it into the channel, and install the end cap as shown in figures C and D.

6. That’s it! Your customized LED light fixture is complete and ready for installation, which we will cover in the next step.

7. Mounting this LED profile is as easy as applying double-sided tape to the back of it and sticking it to your intended surface. Be sure to cut the tape to fit the back of the LED profile and to leave the tape backing on the side not attached to the channel until you are ready to mount it.

For most LED profiles, mounting clips are available for a more permanent installation.

If you have questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

Appliances can make for exciting and valuable additions to your home; however, they use a lot of electricity and can ultimately take a toll on your electrical system. As a Plano TX electrician, I have seen it time and again—homeowners buy new appliances that, even when they have an “Energy Star” label, use a significant amount of electricity. These homeowners are unaware, however, that the more important problem lies in the installation of these devices, taking for granted the safety precautions that were addressed (or not) during the installation process.

The old “set it and forget it” mentality that a lot of people seem to have when it comes to their new appliances is that, whether or not a Plano TX electrician is called to help install the appliance, the importance of appliance installation safety is ignored and the awareness of potential dangers and mistakes in installation is minimized. As a result, things that at the time of installation seemed trivial in the long run can cause significant problems.

Ideally, with the help of a Plano electrician, you should have no problems installing your new electrical equipment. Here are some tips that might help you prevent safety concerns with the installation of your brand new appliances:

Chances are, you don’t need to call your Plano TX electrician to help you with every new appliance installation. However, if you have any doubts or questions about how to install your appliance safely, don’t hesitate to call us at Electric Man so we can make sure that your installation goes off without a hitch.

Give us a call today at 972-792-7270 and connect with us through our website, www.electricmaninc.com. Also, feel free to ask your questions in the comments section of our blog and we will get back to you soon.