RGB LED strip lights are a great way to add a pop of color to your above-ground pool. These low-voltage LED lights can be applied to the inside rim of your pool or around your pool deck. With RGB LED strip lights, you can choose from a ton of dynamic color-changing and single-color modes with adjustable brightness and speed control. They’re great for parties or late-night swims and can be easily installed. We’ve included installation instructions for our waterproof LED strip lights. Some cities require above-ground pool lighting to meet National Electrical Code (NEC) Article 680 standards, which would limit possible pool lighting installation locations. Before you purchase LED pool lights, check your city’s code requirements. We also recommend that you have a certified electrician install your lights.

 

1) Before ordering your LED strip lights, measure the diameter of your pool and multiply by 3.14 to find its circumference; this number indicates the total length of strip that you will need. The 21-foot pool used for these installation instructions has a circumference of 65.94 feet and requires 4 runs of 16-foot LED strips.

You will also need to measure the distance between where your power supply will be and both sides of your pool where the amplifiers will be installed (see the setup and wiring illustration below). These distances will tell you how much 18-gauge wire you’ll need for connecting the amplifiers to power. Make sure to account for the distance of any dips or turns that the wires may take along their paths.

Lastly, measure the approximate distance that will be between your controller and where your strip lights begin. This distance will tell you how much 22-gauge wire you’ll need for connecting the controller to your strips. You will also need two small sections of this wire for connecting your first and second strip lights to the amplifiers.

2) Before you’re ready to install your LED strip lights, be sure to drain your pool. Begin by creating or locating a dry area away from your pool for the power supply. The power supply should be contained in a weatherproof box. Power supplies should be installed between a ground fault circuit interrupter (GFCI) protected circuit and the pool’s junction box. It’s crucial to use a GFCI protected circuit as it shuts off if current flows where it’s not supposed to.

Wire the included plug to the power supply, but do not connect to power until the installation is complete.

3) Connect your RGB LED controller to the power supply. Cut the barrel off of the controller wiring. Strip back the remaining wires, and connect its wires to the power supply.

4) Cut the LC2 connector off of the remaining end of the controller, and strip back the wires. Run 22-gauge four-conductor wire to connect the controller to your low-voltage pool lights; use dolphin connectors to join like-colored wires. Connect your first two LED strip lights to the controller by joining each set of like-colored wire with a dolphin connector. You should be connecting four wires of each color (red, blue, green, and black) together. For added protection, cover all wire connections in this installation with electrical tape.

5) You will apply strip 1 clockwise around your pool rim and strip 2 counterclockwise. If you have a flat surface, use mounting clips to secure the strips in place as you go. If you want to mount the strips under your pool rim, drill small holes in the trusses approximately every 2 feet. Use cable ties to anchor the strip to the truss. You can also use speed nuts or cotter pins for strip anchoring to avoid drilling holes.

Solder a small section of 22-gauge four-conductor wire onto the strip’s end terminals. To reseal the LED pool light strip, slide wires through the holes of a 10-mm end cap, fill the cap with silicone, and slide it into place on the end of the strip. Be sure to cover all of the exposed conductive traces to ensure water resistance. Allow a minimum of two to three hours for the sealant to cure.

7) Once the new end wires are attached to the strip, you will mount the amplifier. Use the double-sided 3M foam pad to mount the amplifier in the middle of strip 1 and strip 3. For best results and added security, apply 3M adhesion promoter to the amplifier and its installation location on the pool wall.

8) Using a dolphin connector, join each like-colored wire on strip 1 to the same color on one end of the amplifier. Do the same when connecting strip 3 to the other side of the amplifier. You should be connecting three wires in each color (red, blue, and green) together on each side of the amplifier. The black strip wire will be joined with white amplifier wire. Note that the separate group of just black and red wires are meant to be connected to the power supply. Follow the same instructions for connecting strips 2 and 4 to the amplifier on the other side of the pool.

9) Use 18-gauge wire and dolphin connectors to connect the amplifiers to your power supply.

10) Plug the power supply’s attached cord into an outlet, and enjoy your LED pool lighting system! Refill your pool with water, but make sure to leave space between the water line and the lights.

For more LED pool lighting options, see our entire selection of waterproof color-changing LED strip lights.

 

For technical questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

Now that you have the holes for lamp sockets, we need to start wiring the lamp sockets.

Kevy, an eCommerce Marketing Automation ​company that specializes in automating and personalizing the shopping experience. ​ ​​Kevy gives online retailers the tools they need to help visitors find the products they care about most. When she is not at Kevy, Brooke and her husband Ryan love creating new projects and are always looking for a new DIY opportunity around the house.

It’s never a good idea to use electricity around water; bathroom spaces always have a certain amount of humidity and steam as well as water in them. You may end up using electrical devices such as hair dryers and shavers when you are in this bathroom and the shower and bathtub areas always have some water. These can prove to be an electrocution hazard or a fire hazard and it’s important to be extra careful when you are using any electrical appliances in the bathroom.

We all need water to maintain health and hygiene. However, it’s also an excellent conductor of electricity. This means you can easily experience shock when you are standing in a water puddle and touch an electrical appliance. If your skin in wet, that gives the electricity an easier path and it can pass through your body in an unhindered manner.

That can be extremely dangerous as electrical shock can cause heart arrhythmia, burns and can damage your nervous system and lead to death too. If the grounding is improper or if the wiring is poorly installed, that can start a fire as well. And so, it is crucial to maintain electrical safety when you are in bathroom spaces.

Here are some useful tips to you can follow to avoid an emergency:

Choosing the right size depends on the level of energy independence that a renewable energy owner wants. It may simply boil down to what you can afford. These levels range from 100 percent or completely off the grid (the most costly), to a simple energy backup for emergencies.

100% energy independence or completely off the grid: this requires a huge investment in terms of generation and storage. In addition, it may require other power sources such as fossil fuels or wind generators.

High energy independence: This requires a solar system with enough batteries to last a few days or even through the winter. PV systems are sized to enable the owner to have surplus energy to store during summer and be self-sufficient through winter without relying too much on the grid. The customer will still rely on the grid for backup just in case there are prolonged days of bad weather.

Summertime independence: Customer installs just enough panels and storage capacity to get through a normal summer day but will have to draw power from the grid during the winter.

Peak time independence: Battery size should be large enough to supply power during peak times when electricity rates are highest.

Reduced reliance on the grid during peak times: Some customers cannot afford to install enough storage to cover their entire peak time usage. In such a case, some will install a system that will enable them to at least reduce part of their grid usage during these times.

Emergency power backup: This requires smaller energy storage, enough to cover a short power outage. Some customers use this together with fuel generators. Battery storage is only required for the short duration from the time grid power goes out, to when the alternative power becomes available.

Even though a solar energy system is a great investment that reduces your electricity bills, it is not possible to completely get off the grid without investing in large storage systems. However, adding modest battery storage to a grid connected to solar systems is a better way of increasing your independence from the grid without spending too much.

Most marketers have online tools that can help you get the right size battery based on various factors. However, it is advisable to consult professionals for the best advice.

Customers with solar systems are increasingly adding battery storage to reduce their electricity costs or become independent from the grid. With better technology and prices getting lower every day, battery storage is becoming an appealing component to many solar power system owners.

This type of storage allows the customer to charge their batteries during the day and then discharge them when there is no generation. This permits homeowners and businesses to have a backup power source and save on electricity bills. In addition, you can sail through cloudy periods or other times when power generation is low.