If you’re in the midst of a renovation or simply rearranging your floor plan, then you’ve likely come across the need to add or relocate a light fixture. Maybe your new dining room table is a little wider than the old one, you’re adding a kitchen island with pendant lights, or you’ve finally convinced your significant other to let you get that pool table you’ve always wanted. In any case, you need to move or add a light fixture – but how and when?

First, it should be noted that, contrary to how it may seem, most light fixtures are not connected to a joist or even drilled into wood. Instead, hanging light fixtures and ceiling lights alike are located between joists and supported by electrical boxes that grip a wide surface area of the sheetrock that makes up your ceiling to support the weight of the fixture below; for heavier fixtures, like large chandeliers or ceiling fans, there are larger, even joist-secured boxes that will need to be used.

If you’re moving a light fixture, it is important to note that there are certain limitations as to where the fixture itself can go. If you wish to relocate the fixture to a place where a joist exists just above, then you’re likely going to have to use a swag hook and chain to anchor the fixture in place, as a box under a joist is not an option. That said, if you’re moving the housing for the fixture itself, you’ll need to know which direction the joists above run, then choose to move it either through the same joist cavity or drill through a joist to run the current wiring to the new housing. Other things to consider include which switch controls the light and where it is located, as it is a safe bet that a wire will have already crossed all joists above (at some point). This can prevent your electrician from drilling needlessly by allowing them to fish the wire back to the earlier point. If your switch is further away than the destination, you can bet they’ll have to do some drilling. Jumping through, between, and around the joists in the ceiling represents the largest obstacle your electrician (and light fixture) will face.

Once your location is set, all that is left is to get your electrician out to assess and perform the work for moving your box. If you’re planning on doing one large fixture over a pool table, island, or entire room, then you’ll want to take into account the power output of the fixture compared to what that circuit can safely allow for as well as the weight of the fixture. A typical rule of thumb is that anything under about 35 pounds can be handled by a standard drywall box, but something more (or with a fan) will need extra stabilization. Surprisingly, if you’re running numerous small pendant lights, the electrician may have an even easier time running the circuit and ensuring that your lights are up and running in no time. Just be sure to discuss the fixtures you have in mind with your electrician before you purchase them to know what they believe your limitations are!

Whenever you need electrical work done around your Des Moines home, contact the experienced professionals at Electrical Gurus. We are proud to offer the finest licensed local electricians in the area and are always more than happy to help out on your household projects.

When you think about homes that rely on solar energy, you may think of rustic cabins that live in a very primitive fashion. That may have been the case 20 years ago, but today, some of the most luxurious homes are run off of solar power. There have been plenty of innovations and upgrades made to the world of solar energy and homeowners across the country are taking advantage. You don’t have to go all in if you don’t want. That is the beauty of solar energy. Your electrician in California can answer questions you may have about how you can make solar energy a part of your home. The team at The Electric Connection is well versed in the latest technology and can provide you with the information you need.

You have several options. The first and probably the most popular is to remain connected to the power grid. Basically, you use the solar energy you have and when it is depleted, your home relies on the main power grid or the electricity from the electric company. Even this small change can result in a great deal of energy savings in California homes and businesses. Every little bit matters and using solar power to run your home during the day and relying on the power grid when there is very little demand at night is an excellent choice.

You can choose to rely completely on solar power if you want. This will require the installation of a solar panel system that can run you upwards of $20,000 depending on the size of your home and your electric demands. Even though it is a big initial investment, there are tax breaks and you won’t be paying a monthly electric bill so it kind of balances out.

If you would just like to dabble a bit in alternative energy, consider starting with a solar powered water heater. This one change can save you a great deal of money on your electric bill. Again, every little bit helps. Give The Electric Connection a call today to take your first step into the world of solar power.

Every summer, more and more homes experience outages in their electric systems. As a top Dallas Electrician, my electricians and I see the effects of these outages every day. They can be devastating, and cause a lot of damage.  In fact, the insurance industry pays out over $1 billion in damages annually in claims caused by outages and power surge damage. Most outages are caused by the weather, but there are different kinds of weather can cause an outage. This even includes weather that doesn’t produce lighting damage like the massive ice storms we saw during Super Bowl week this year that left hundreds of thousands without power (and, more importantly, without heat!) during one of the worst winter storms in years. Summer storms can produce devastating tornadoes that can knock out power for miles around the area they touch down in, and many hurricanes begin to build in the summer and early fall, causing catastrophic results even outside of the disaster zone. Hurricane Ike left over two million people without power when it hit southeast Texas in 2008, and not all of them were in the impact zone.

Not every outage comes from something as dramatic as a hurricane or tornado.  A lightning strike, even as far as half a mile away, can potentially cause damage to your delicate electrical equipment and appliances. Often, large-scale outages can occur when lightning strikes a transformer.

Outages don’t just occur because of bad weather:  many outages are caused by power equipment switching to accommodate the heavy load people put on the power grid.  Our power grid is already having trouble with its current load, and the problem only grows as more and more people use more and more electricity.  Summer in Dallas and Fort Worth is the perfect examples.  It’s when people are running their air conditioners constantly. This puts an incredible load on local and state power grids.  This leads to government agencies putting out warnings almost every summer about potential power outages, threatening brownouts and blackouts unless people conserve energy.

These outages aren’t damaging in themselves, but they leave open the possibility for electrical power surge damage.  You’ve probably noticed that when the power comes back on after an outage, it often flickers on and off quickly as the power grid attempts to get the electricity flowing back into your lines.  This stop-and-start action creates surges that can easily damage unprotected electronics or appliances.  Having a nice TV damaged like this is a very expensive hassle, and you can imagine how much more expensive and uncomfortable it could be if the surge takes out your air conditioner and refrigerator!

So, what can you do to keep power outages and power surges from affecting you?

Some of these options can even help you save money on your electric bill without the hassle of gas, fumes, or noise pollution.