RGB LED strip lights are a great way to add a pop of color to your above-ground pool. These low-voltage LED lights can be applied to the inside rim of your pool or around your pool deck. With RGB LED strip lights, you can choose from a ton of dynamic color-changing and single-color modes with adjustable brightness and speed control. They’re great for parties or late-night swims and can be easily installed. We’ve included installation instructions for our waterproof LED strip lights. Some cities require above-ground pool lighting to meet National Electrical Code (NEC) Article 680 standards, which would limit possible pool lighting installation locations. Before you purchase LED pool lights, check your city’s code requirements. We also recommend that you have a certified electrician install your lights.

1) Before ordering your LED strip lights, measure the diameter of your pool and multiply by 3.14 to find its circumference; this number indicates the total length of strip that you will need. The 21-foot pool used for these installation instructions has a circumference of 65.94 feet and requires 4 runs of 16-foot LED strips.

You will also need to measure the distance between where your power supply will be and both sides of your pool where the amplifiers will be installed (see the setup and wiring illustration below). These distances will tell you how much 18-gauge wire you’ll need for connecting the amplifiers to power. Make sure to account for the distance of any dips or turns that the wires may take along their paths.

Lastly, measure the approximate distance that will be between your controller and where your strip lights begin. This distance will tell you how much 22-gauge wire you’ll need for connecting the controller to your strips. You will also need two small sections of this wire for connecting your first and second strip lights to the amplifiers.

2) Before you’re ready to install your LED strip lights, be sure to drain your pool. Begin by creating or locating a dry area away from your pool for the power supply. The power supply should be contained in a weatherproof box. Power supplies should be installed between a ground fault circuit interrupter (GFCI) protected circuit and the pool’s junction box. It’s crucial to use a GFCI protected circuit as it shuts off if current flows where it’s not supposed to.

Wire the included plug to the power supply, but do not connect to power until the installation is complete.

3) Connect your RGB LED controller to the power supply. Cut the barrel off of the controller wiring. Strip back the remaining wires, and connect its wires to the power supply.

4) Cut the LC2 connector off of the remaining end of the controller, and strip back the wires. Run 22-gauge four-conductor wire to connect the controller to your low-voltage pool lights; use dolphin connectors to join like-colored wires. Connect your first two LED strip lights to the controller by joining each set of like-colored wire with a dolphin connector. You should be connecting four wires of each color (red, blue, green, and black) together. For added protection, cover all wire connections in this installation with electrical tape.

5) You will apply strip 1 clockwise around your pool rim and strip 2 counterclockwise. If you have a flat surface, use mounting clips to secure the strips in place as you go. If you want to mount the strips under your pool rim, drill small holes in the trusses approximately every 2 feet. Use cable ties to anchor the strip to the truss. You can also use speed nuts or cotter pins for strip anchoring to avoid drilling holes.

Solder a small section of 22-gauge four-conductor wire onto the strip’s end terminals. To reseal the LED pool light strip, slide wires through the holes of a 10-mm end cap, fill the cap with silicone, and slide it into place on the end of the strip. Be sure to cover all of the exposed conductive traces to ensure water resistance. Allow a minimum of two to three hours for the sealant to cure.

7) Once the new end wires are attached to the strip, you will mount the amplifier. Use the double-sided 3M foam pad to mount the amplifier in the middle of strip 1 and strip 3. For best results and added security, apply 3M adhesion promoter to the amplifier and its installation location on the pool wall.

8) Using a dolphin connector, join each like-colored wire on strip 1 to the same color on one end of the amplifier. Do the same when connecting strip 3 to the other side of the amplifier. You should be connecting three wires in each color (red, blue, and green) together on each side of the amplifier. The black strip wire will be joined with white amplifier wire. Note that the separate group of just black and red wires are meant to be connected to the power supply. Follow the same instructions for connecting strips 2 and 4 to the amplifier on the other side of the pool.

9) Use 18-gauge wire and dolphin connectors to connect the amplifiers to your power supply.

10) Plug the power supply’s attached cord into an outlet, and enjoy your LED pool lighting system! Refill your pool with water, but make sure to leave space between the water line and the lights.

For more LED pool lighting options, see our entire selection of waterproof color-changing LED strip lights.

For technical questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

If you’ve read our blog for any length of time, you know we’re pretty enthusiastic about light. At Pegasus Lighting, we love writing about lighting design, technology, news, advice, art, and more. BUT we also love to read about it. For today’s post, I decided it was high time to send a shout-out to some of our favorite lighting blogs, magazines, and websites. Each one is run by passionate individuals and offers a unique perspective on the lighting industry. And you better believe they keep us on our toes.

So without further ado…

To indulge your inner lighting geek, check out Lighting Science’s company blog. You’ll learn things like how lighting affects sea turtle behavior, what it can do to our sleeping patterns, and more. The best part – Lighting Science is actively solving these problems with new, creative lighting technology!

Here’s a bright post:

Lighting designer James Bedell shares his unique blend of expert knowledge, honest opinions, and passion for lighting on his personal blog, and it’s well worth a read. Some days he’ll share practical tips about how to light your home, while other days might be some fascinating insight about what we can learn from a sunrise.

Here’s a bright post: 

When you’re in the mood to look at something pretty, or cool, or crazy, it’s time to navigate over to Lightopia’s Light Public. The lighting enthusiasts on this blog post about commerical lighting design, fine art, and photography mostly – and it will blow your mind.

Here’s a bright post: 

Are you planning on having lots of family and friends over this holiday season? Maybe you are hosting a lavish party or a quaint dinner party. Whatever the case may be, wouldn’t it be nice if you had a little more space or if your kitchen was setup a little differently to make cooking for a large party easier? There is no better time to remodel your home. Consider it an early gift for yourself. A gift that will add value to your home while making it a little more enjoyable for you to live in. If you are ready to make that basement remodel or kitchen remodel happen, now is the time. Your electrician in Beverly Hills, like the team at The Electric Connection, is here to help.

You will likely need to hire a contractor to do the remodel. It makes it easier and you can keep up with your busy life. A remodel will involve some Beverly Hills electrical work. Whether you are tearing down walls, adding on a room or moving appliances around, you will need an experienced electrician to complete the wiring portion of the remodel. Meet with the electrician and discuss what it is you need. If you need extra outlets on one side of the room or would like data lines in a certain place, communicate that to your electrician.

It is important you choose an electrician who will work well with your contractor. Being licensed to perform the work is also an important factor. Remodels will require permits from your county building department. You want to make sure the wiring passes inspection the first time. By hiring a qualified electrician you can ensure the process will go smoothly and your remodel is finished in time for the holidays. Give The Electric Connection a call today and get started transforming your home.