Some electrical repairs just can't wait. If you discover loose wiring, a faulty circuit or other problem in your home electrical system, it is essential to call an electrician immediately. At best, electrical problems can be annoying. At worst, they can damage your appliances or even start a fire in your home. That's why it's so important to have savings on hand so you don't feel compelled to delay emergency electrical repairs. Unfortunately, far too many families are not prepared financially to cover this type of emergency.

Emergency Savings Not Cutting the Mustard

The savings profile of the average American family leaves a lot to be desired. A recent report pointed out that 25 percent of homeowners in the United States don't have any money at all saved to protect themselves in case they need an emergency electrical repair or other home service. What's more, about half of the families that do have savings have less than $1,000, which might not be enough to cover a major bill.

And you never know when you might need help. In fact, nine percent of households said they had a problem with a circuit, switch or outlet in the past year, according to the report. Unless you are already an accomplished electrician, these are not problems you can address by yourself – you need to hire a professional in order to protect the safety of your home and your family. If you don't have any savings, that means borrowing money or putting off a repair – a dangerous prospect.

Make Sure You Have Money When You Need it

Follow these tips to increase the odds that you have cash on hand when you need it:

Expert Electricians Keep You in Safe Hands

Maintenance and repairs on your wiring and circuits are tasks you simply cannot put off. Whether the electrical work you need is routine or a true emergency, call upon a professional electrician to get the job done safely and promptly.

Other parts of the country may be warming up and getting ready to use our air conditioners, but we’re still relying on our heaters to get us through more than a few chilly nights. So if yours begins to malfunction, you may start to panic. This is understandable, but know that if you’ve had your system maintained before the heating season began, it may likely not even be an issue with the system itself.

Instead, you may be in need of Newton, MA electrical wiring services for some component of your heater. Keep reading to learn more about how your heater can be impacted by electrical issues.

This applies to both electrical furnaces as well as boilers. Both of these systems use heating elements—a set of coils that burn hot as a current passes through them—in order to raise the temperature of the air (furnaces) or water (boilers).

Both of these systems contain more than one heating element. Therefore, if you one fails you likely won’t lose your heat entirely, but your heater won’t be able to work as efficiently as it otherwise would.

If you’re utilizing a heat pump, then this is the most common electrical problem you might run into. Capacitors are cylindrical devices about the size of a soda can, responsible for sending electrical charges to the motors to start and keep them running.

Capacitors can burn out after years of use, or suffer from wiring issues, causing the heat pump to “hard start” (draining power) or quit functioning all together. You’ll need a professional to replace the damaged electrical capacitors.

Even if you have a heater that runs off of natural gas, oil, propane, or geothermal power, it’s going to have an electrical thermostat controlling it. Thermostats with failing wiring will begin to malfunction, often incorrectly registering your home’s temperature or failing to accurately set the heater. If your heater is failing to reach its target temperature with no other signs of a problem, your thermostat wiring could certainly be to blame.

Regardless of bends, twists, or turns, Example of a cut line on LED strip lights

2. You will now have two LED strip lights. Carefully peel back the end portion of the paper strip covering the strip’s adhesive backing, and then remove the 3M VHB adhesive from the solder pads on the bottom side of one of the strips. The strip with its adhesive peeled back will be the top strip when soldered.

5. Align the non-tinned strip segment (strip with adhesive removed) directly over the newly tinned pads, and apply heat. Hold the soldering iron in place until the solder remelts and begins to flow. To strengthen the bond and improve visual appeal, a small portion of solder can be added to the top pad.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split and solder a run of non-weatherproof two-conductor or connecting wires. Peel away the blue wire so that only the positive (red), negative (black), and control (green) wires are left.

*No wires should be peeled away if you’re joining single-color or standard RGB light strips.

3. Properly heat your soldering iron. For best results, clean and tin the tip of the iron immediately before soldering. To tin the iron, touch solder to both sides of the iron’s tip.

4. Next you will need to tin the solder pads on both ends of the split strip light. When soldering, always apply heat to the target area on the strip and not directly to the solder. Once sufficient heat has been applied to the area, start introducing solder.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split, solder, and reseal a

3. Follow steps two through five located at the top of this post for soldering a standard RGB strip light.

4. To reseal the strip light, apply

The LED strip lights are now connected, and power should flow through the entire length of the weatherproof strip.

By: Jason Lee

Halloween is over which means the holidays are officially here. That means the relatives are on their way and you’ll be using your large appliances more often causing your electric bill to look scary long after Halloween has ended. Don’t let the increase in relative visits and vampire electric devices drive up the electric bill.

To keep the electric bill down, remember to only use the dishwasher when it is full. Running the dishwasher when it is only half full will amount to a lot more energy consumption.

Items like washers and dryers are guilty of consuming more energy during the holidays too. Washing clothes in cold water and setting the dryer on low heat will help in reducing the electric bill.

Knowing when to say goodbye to your old system is another way to save on energy. Older appliances run up the electric bill. If you have an appliance that is over 10 years old, consider replacing it with a newer, energy efficient model.      

It is also a good idea to have all large household appliances connected to their own dedicated circuit. To many of these large appliances operating at the same time on the same circuit can cause a blown fuse or a tripped breaker. A dedicated circuit for each large electrical household appliance will keep this from happening.

Lastly, don’t let your everyday electrical devices like laptops, cell phones or tablets get greedy and hog the power outlets. Only charge these items when they need it.                                                     

You’ll have enough to worry about as the holidays set in. Take the electric bill off the list by doing these simple energy savings tips from Mr. Electric.