By providing early warning in the event of fire, smoke detectors can allow you and your family sufficient time to reach safety. Experts report that you can increase your chances of surviving in a home fire by 50% simply by having smoke detectors. Click here for more information about installing  smoke detectors in Los Angeles, my electrical company’s service area.

If your house was built before 1950, it likely has electrical wires with cloth insulation. Over time, the cloth dries out and becomes brittle. Eventually, it crumbles off the wire, exposing bare wires that can short-circuit and cause shocks or fires. Old cloth-insulated wires should be replaced with plastic-insulated wires. Plastic insulation lasts indefinitely and completely resolves the safety issue. Click here for more information about replacing cloth  wiring insulation.

The National Electrical Code requires that outlets in the vicinity of water be equipped with a device called a “Ground Fault Circuit Interrupter” or GFCI (also called GFI). GFCIs are required in all bathrooms, kitchens, garages, pools, and some outdoor areas. GFCIs can protect your family against deadly electrical shocks and are inexpensive to install. Click here for more information about GFCIs and GFIs.

Knob & Tube wiring gets its name from the white ceramic knobs around which wires were wound and the short ceramic tubes through which wires were guided. This type of wiring is usually found in homes built before 1935. In the Los Angeles and some other parts of the country, knob and tube can sometimes be seen in houses built as late as 1950. My electrical company specializes in replacing Knob and Tube wiring in the L.A. area — much of it is in Pasadena and other parts of the San Gabriel Valley.

Knob & Tube systems use old cloth-insulated wires and are not grounded. We strongly recommend that Knob & Tube wiring be replaced to eliminate fire and electrical shock hazards.

An electrical surge is a sudden increase in power that flows through electrical wires. Surges can cause damage to computers, phones, entertainment systems, microwaves, stoves, fridges, washers – any device that has electronic components such as sensors and timers. Today, that’s most appliances. A Whole House Surge Protector can save your appliances and electronic devices and save you thousands of dollars in damage.

Look for our $50 discount coupon for the installation of whole house surge protectors at www.theelectricconnection.com.

A properly grounded electrical system routes occasional leaking electricity through a “ground wire” into the ground. Without grounding, excess electricity can cause fires, damage to electrical appliances and computers, and also shocks to residents.

Older homes built under earlier electrical codes will often have outlets for two-prong plugs. This is often an indication of an ungrounded electrical system. Sometimes, the outlets have been replaced with the modern three-prong type, but without actually adding a ground wire. This can make it appear that the system is grounded when it’s not.

Even when your wiring system has a ground wire, the grounding may fail due to loose or corroded connections and splices. A qualified electrician can check your wiring with a special tester to determine if it’s fully grounded. The Electric Connection offers this testing as a free service with every electrical job that we do in the L.A. area.

There is now conclusive evidence that both Zinsco and Federal Pacific Electric (FPE) “Stab-Lok” electrical panels can fail. (Electrical panels contain your circuit breakers or fuses.) Fires and electrical shocks can result. These brands were installed in the 1950s to 1980s. The failure rates as they age are much higher than for other brands and represent a real electrical hazard. We recommend all Zinsco and FPE electrical panels and circuit breakers be replaced with modern electrical equipment. Click here for more information about Zinsco and Federal Pacific electrical panels. One of the specialties of The Electric Connection is panel upgrades. We’re possibly the most active company in Los Angeles when it comes to electrical panel replacements. We offer a free safety check of your L.A. electrical panel box with every job.

Circuit breakers and fuses protect your electrical wiring from overloads of electricity. Overloading can melt wires and cause fires and electrical shocks. Whenever a wire is overloaded, the circuit breaker or fuse is supposed to cut the flow of electricity.

Sometimes older circuit breakers don’t work fast enough and allow too much current through. Fuses can also be a safety concern. Sometimes, they’ve been replaced with improperly-sized fuses and no longer protect wires from overloading. These safety issues can be solved by installing modern circuit breakers. Click here for a coupon for a free check of your electrical circuit breaker box with your next electrical job.

Most homes have copper electrical wires. However, from the mid-1960s to the mid-1970s, over 2,000,000 U.S. homes were wired with aluminum. The U.S. Consumer Products Safety Commission has determined that aluminum wiring is hazardous as, over time, connections and splices can fail, resulting in fires and shocks.

Fortunately, a qualified electrician can upgrade an aluminum wiring system without replacing all the wires with copper. It’s possible to eliminate the fire hazard by upgrading only connection points and splices. Aluminum wiring safety retrofits should be done only by electricians specifically trained to upgrade aluminum wiring safely.

If you think it’s possible that your Los Angeles home has aluminum wiring, you can get a free checkwith your next electrical job. One of the specialties of The Electric Connection is efficient and effective safety upgrading of aluminum wiring in the Los Angeles area.

Click here to visit our website.

Using a warm white or RGB COB (chips-on-board) LED, these flood lights emit up to 1,000 lumens of illumination in a wide 120-degree beam pattern. The weatherproof LED fixtures have a low-profile die cast aluminum housing with an integral heat sink and a tempered glass lens. An adjustable mounting bracket is also included to direct illumination where it’s needed.

If you live in Maryland, Northern Virginia, or Washington, DC, there’s a good chance you’ve seen one of Kolb Electric’s bucket trucks driving around! Our bucket trucks allow us to expand our service line far beyond that of most electricians in the area, and overall, they’re pretty great! These are a few of our favorite things about our bucket trucks:

The best thing about our bucket trucks is also their most defining feature—their height! Our trucks can reach up to 50 ft. Thanks to the lift we get from the cherry pickers, we can work on utility poles and parking lot lights as well as large industrial structures and anything else that requires a little extra lift.

Even up that high in the air, our bucket trucks keep our electricians safe. The buckets are designed to reach about waist height, meaning there’s very little risk of anyone actually falling out. Best of all, if something does happen—the weather turns bad, for instance—they’re easy to move out of dangerous areas.

Though they might seem big and complicated, once you get down to it, bucket trucks are pretty easy to use! A set of controls inside the cab controls the crane, while another set inside the bucket itself allows the rider to raise and lower him or herself while up there.

Not only that, but our bucket trucks also have space to hold all of our equipment, meaning we’re always prepared for jobs that involve going up high.

Our bucket truck fleet has helped us become one of the most well-known electrical service companies in the MD-DC-VA area. If you need utility pole, parking lot lighting, or any other services that require a bucket truck, call Kolb Electric today!

Click here to read more about our bucket truck services »

If you live in an older home, you probably have wiring that was designed to support far less voltage than the demands of today’s modern equipment, like computers and home entertainment centers. The wiring might also be starting to decay, leading not only to potential power losses, but fire hazards as well. In many cases, you should invest in at least partial—if not whole-house—rewiring to upgrade your home so it can handle the electrical load and prevent hazards.

Here are a few signs to look for that may warn you it’s time for wiring replacement.

GFCIs or ground fault circuit interrupters are safety devices that have been extremely effective in reducing the total number of home electrocutions by almost 50%, in Australia. Most new homes and businesses now have these devices installed in locations where water is present in and around the premises. It’s important that electrical installations in outdoor locations be protected from wind and rain; that’s the one way to prevent shock hazards.

Before we understand what a GFCI is, let’s understand what a ground fault is. It is the unintentional flow of electrical current between the source and any grounded surface. If the electrical installation isn’t properly protected, an individual that comes into contact with an energised part can suffer an electrical shock.

For instance, if the person is holding any deteriorated electrical cord attached to the hair dryer, and it happens to touch a plumbing fixture they are using, they can get electrocuted and will suffer a painful shock.

This small receptacle has “test” & “retest” buttons on it. It may sometimes be built into circuit breakers that are installed in the main electrical panels. When electricians are conducting an electrical audit, they also test whether the GFCIs are functioning properly. They might also recommend that you get GFCIs installed in the vicinity of plumbing fixtures.

These are extremely useful electrical safety devices which trip the electrical circuits in case they detect any leakage current or ground fault. An individual that’s become the pathway for a leaked current can get a severe shock or will get electrocuted. It is important to get GFCIs installed in any outdoor or indoor areas where you feel that water might come in contact with the electrical installations or fixtures you have on your property.

Ideally, the areas where GFCIs should be installed include:

It is important that these devices be checked with regularity. If you have opted for an electrical maintenance contract, the electricians will ensure that the GFCIs are checked along with all the other installations; this will help confirm they are working as they should and that they provide the necessary safety to those living or working on your premises. You can also test the GFCIs on your property, by following these basic steps:

If you aren’t too sure about whether you have GFCIs installed at the right points on your property, call in your local electrician. They will inspect all the fixtures and inform you if GFCIs have to be installed in any specific rooms or outdoor spaces. Aside from this, they will also audit the rest of the installations and tell you if any upgrades are required.