Regardless of bends, twists, or turns, Example of a cut line on LED strip lights

2. You will now have two LED strip lights. Carefully peel back the end portion of the paper strip covering the strip’s adhesive backing, and then remove the 3M VHB adhesive from the solder pads on the bottom side of one of the strips. The strip with its adhesive peeled back will be the top strip when soldered.

5. Align the non-tinned strip segment (strip with adhesive removed) directly over the newly tinned pads, and apply heat. Hold the soldering iron in place until the solder remelts and begins to flow. To strengthen the bond and improve visual appeal, a small portion of solder can be added to the top pad.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split and solder a run of non-weatherproof two-conductor or connecting wires. Peel away the blue wire so that only the positive (red), negative (black), and control (green) wires are left.

*No wires should be peeled away if you’re joining single-color or standard RGB light strips.

3. Properly heat your soldering iron. For best results, clean and tin the tip of the iron immediately before soldering. To tin the iron, touch solder to both sides of the iron’s tip.

4. Next you will need to tin the solder pads on both ends of the split strip light. When soldering, always apply heat to the target area on the strip and not directly to the solder. Once sufficient heat has been applied to the area, start introducing solder.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split, solder, and reseal a

3. Follow steps two through five located at the top of this post for soldering a standard RGB strip light.

4. To reseal the strip light, apply

The LED strip lights are now connected, and power should flow through the entire length of the weatherproof strip.

/foot)

Strips with more LEDs per foot will consume more power.

In short, if maximum energy efficiency is what’s most important to you, choose a light strip with smaller LEDs and fewer LEDs.

In order to ensure your LED power supply doesn’t overheat and fail prematurely, we use this general rule of thumb:

Make sure the total wattage of your LED strip lighting is at least 20 percent less than the power supply’s rated wattage.

For example, if you have an LED strip light that requires 80 watts of power to run, you’ll need a power supply that’s rated for at least 96 watts.

The vast majority of our strips include wattage per foot right on their product pages.

power supplies range from six watts to 1,500 watts for compatibility with a wide variety of LED strip lights.

Let’s take a look at an example:

It’s important to verify that the voltage of the power supply you choose is compatible with the voltage of your LED strip lighting. Also, be sure that the power supply’s input voltage matches that of the location it will be installed in. If you have an LED strip with 12-volt DC operation that you wish to use in a 120-volt AC home wiring system, you’ll need a power supply that includes 120 volts in its input range and has 12-volt DC output.

Another factor to take into account for longer runs is voltage drop. A significant voltage drop is present after a certain distance of LED strip. After this distance, there will not be enough voltage present to light the next length of strip. This varies depending on the type of strip and length being used. Usually, a single-density strip (nine or less LEDs per foot) will need to run back to a power source every 32 13/16 feet (10 meters). A high-density strip (18 or more LEDs per foot) will need to run back to a power source every 16 3/8 feet (5 meters). Please refer to “Max Run” in the specifications table of the strip light to determine how many can be run continuously without a parallel run back to power.

3) the 4) if you want your strip to be dimmable

power supply calculator on the product pages of all of our LED strip lights!

There are a few steps involved:

Step 1: Select your strip and the length you need.

Step 3: Click the green “Power Supply Calculator” tab, and select your product by choosing it from the list OR by pasting the exact part number in the search bar.

Step 4: Enter the number of strips at the desired length you’ve selected and voila! You’ll see a list of all compatible power supplies with the best match at the top of the list!

When dealing with electronics, safety is paramount, and you want everything to work like it’s supposed to. So if you’re still not sure which power supply to use for your LED strip lighting project, just reach out to our technical support team or customer service department at 866-590-3533. Our teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

Come check out our booth at The Iowa Home Show January 15-17 at the Iowa State Fairgrounds! Featuring on Saturday country music artist Matt Snook!  And seminars with Design Star Winner Jennifer Bertrand both Saturday and Sunday!  You will also be able to tour 2 complete homes!  Custom Electrical Services at The Iowa Home Show!  Friday 1-7 , Saturday 10-7 , Sunday 11-4.

Please come out and see all the vendors and stop at the Custom Electrical Services booth.  Custom Electrical Services at the Iowa Home Show will have a variety items on display.  Check out the latest LED options for your home.  Inquire about a whole house backup generator.  Upgrade some electrical devices and more!  Please print the coupon photo and enjoy a complementary buy 1 get 1 free entry coupon!

Of course you will want to check out the Custom Electrical Services booth at The Iowa Home Show, there will also be a large variety of vendors. Ranging from general contractors, remodeling contractors, flooring and tile vendors, countertop vendors and more!  If you coming for ideas, trying to find a contractor, or just looking for something to do.  Please come out and say hi!