Summer is in full swing which means you’re likely spending more time in a hot tub. If you don’t currently own a hot tub but are considering getting one in the near future, there are some important things to consider before purchasing. It’s a no brainer that water and electricity don’t mix; therefore, adhering to proper safety and electrical protocol with hot tub installation and maintenance is imperative. Listed below are Expert Electric’s 5 tips for hot tub safety:

You might consider yourself to be quite the handyman; however, setting up a brand new hot tub is an entirely different animal. Wiring a hot tub is no easy task and it’s far more complex than setting up your average home appliance. Consulting a licensed electrician for a hot tub installation will often save you time, money, and a trip to the hospital. A licensed electrician will minimize any costly mistakes you would make that could result in permanent damage to the hot tub and a void in the hot tub manufacturer’s warranty. Additionally, they will ensure you’re getting the best value in all of the necessary accessories that need to be purchased for installation.

Although this usually isn’t a problem if your home was built within the past 30-40 years, it’s always a good thing to look into before adding an additional appliance to your home. This is another area that a licensed electrician can help with. It’s also crucial to understand what type of voltage your hot tub is running with. Smaller hot tubs usually require 120 volts whereas larger hot tubs will often run on 240 volts. Understanding the different requirements associated with your specific hot tub’s voltage and how it relays to its power source is key.

When it comes to hot tub installation, it’s all in the wiring. Using the proper wiring is critical to the functioning and safety of your hot tub. It’s important to use wiring that is able to handle the heat. A licensed electrician will be able to answer any questions you have about wiring and determine which type of wiring is necessary for your hot tub.

Did you know that Canada has a set of electrical codes that must be followed when installing and maintaining any type of electrical equipment in Canada? These codes must be followed accordingly during the installation. The Canadian Electric Code is a handbook that can be purchased online; however, it’s a long read and fairly expensive. Hiring a licensed electrician will save you the chore of reading it and void its additional cost.

Before installing a hot tub, it’s imperative to consider its location. You’ll need room for the hot tub as well as extra room to get in and out. The hot tub should be at least 10 feet away from any overhead power lines and 5 feet away from the removed spa panel. It’s also important to consider how the tub will connect to its power source.

For further information on hot tub installation and the necessary electrical requirements, please visit our contact page for a local number near you or to fill out one of our online forms. Our team of licensed electricians are here to help ensure your hot tub gets installed safely and efficiently.

The home electrical system consists of various components that enable the safe delivery of energy to different sections and appliances in the household. Even though the system may appear complex, it is important for the homeowner to understand a few basics.

This would help you when things do not work or there is an emergency that requires turning off circuits or the entire installation. In addition, an understanding of the home electrical system will help the owner respond to questions from prospective buyers.

All the electrical circuits in the house originate from the main breaker panel. The panel is usually inside the house and near to the power entry point. However, the panel can also be far, and especially when in a multi-family structure.

The rating of the panel determines the number of circuits and power that the home electrical system can support. Some older homes have been using the 100 Amp service, smaller installations use a 60 Amp service while newer and larger houses are built with 200 amps to accommodate the increased number of electrical and electronic equipment commonly used in a modern household.

Different loads require the correct size of cables and breakers that can handle the current without heating up. For example, an air conditioner requires a 30 amp circuit while a kitchen may use two 20 amp circuits.

If there is a fault, such as a short circuit or overload, the breaker trips and cuts off the power to the affected circuit, hence preventing further damage that could lead to fire. Before resetting the breaker, you should first ask an electrician to check and rectify the problem.

A home electrical system consists of different individual circuits originating from the main breaker panel. The wires from the panel run to the rooms to supply the outlets, lights, and hand wired appliances. In most cases, several rooms may share the same circuits such that all the lights in the house are on one breaker, outlets on another breaker, etc.

Some dedicated circuits from the main breaker may go directly to the hard-wired appliances and nowhere else. Equipment such as the electric water heaters, furnaces, and air conditioners are usually installed on their own. Other hard-wired devices include the smoke alarms, which may also have battery backups so they will work even when there is a power outage or a fire interrupts the home electrical system.

Grounding is an essential protective feature that must be installed in all home electrical systems. It provides a path for the electrical current arising from faults that make the exposed metallic parts to become live and dangerous.

The ground connects all the exposed metallic parts to the earth mass through a third wire in the power cord to the equipment. This provides a low electrical resistance path for the current, hence, making the parts safe to the touch even in the event of a malfunction.

maintenance and repairs.

There are plenty of reasons to install new indoor light fixtures in your home. Perhaps you want to update your interior aesthetic, or save energy by upgrading to efficient LED bulbs. Maybe you even want to bring your lighting into a smart home control system. Although wiring a new fixture is usually a simple job, complications can crop up if your home still uses an outdated wiring system. In order to comply with your local building code, you may have to perform some extra electrical work to ensure the safety of your new fixture. Read on to learn more.

Bringing Older Electrical Work Up to Code

If your home still uses knob-and-tube wiring, the law prohibits connecting new light fixtures to the old wiring. You don't have to replace the entire wiring system itself, although that’s not a bad idea, because it can reduce your risk of an electrical fire and lower your insurance rates. Even if you don't have the time or money for such extensive electrical work, though, you can remain in compliance with your local code by installing an electrical box between your wiring and the light fixture.

You can purchase an appropriate electrical box at most local hardware stores – but make sure you verify that it is designed to meet local code guidelines for installing new light fixtures. From there, after you turn off the power to the room, you have to cut a hole in the wall where you want the fixture to go, large enough for the box to fit. If you're lucky, the fixture will be near a stud or part of the frame so you can mount the box easily. Otherwise, you have to cut the wall extremely carefully to ensure you leave enough lath and plaster keys to support the box.

Wiring the New Light into Place

Next, once the box is ready to be installed, follow the manufacturer instructions to clamp in the home wiring to the back of the unit. You may have to add a ground wire as well, depending on the specific scenario. Anchor the box using metal supports, and when it's all in place, connect the light fixture. When everything is securely connected, you can turn the power back on and give your new light a trial run.

Remember, knob-and-tube wiring can be a fire hazard, and performing electrical work in general can be dangerous if you don't know what you're doing. If you have any doubts or questions about installing your new light fixture, the best route is to have a professional electrician give you a hand.

Expert Assistance with Your Electrical Work

For assistance with all your electrical work, including installing new light fixtures, contact a qualified residential electrician today.