RGB LED strip lights are a great way to add a pop of color to your above-ground pool. These low-voltage LED lights can be applied to the inside rim of your pool or around your pool deck. With RGB LED strip lights, you can choose from a ton of dynamic color-changing and single-color modes with adjustable brightness and speed control. They’re great for parties or late-night swims and can be easily installed. We’ve included installation instructions for our waterproof LED strip lights. Some cities require above-ground pool lighting to meet National Electrical Code (NEC) Article 680 standards, which would limit possible pool lighting installation locations. Before you purchase LED pool lights, check your city’s code requirements. We also recommend that you have a certified electrician install your lights.

1) Before ordering your LED strip lights, measure the diameter of your pool and multiply by 3.14 to find its circumference; this number indicates the total length of strip that you will need. The 21-foot pool used for these installation instructions has a circumference of 65.94 feet and requires 4 runs of 16-foot LED strips.

You will also need to measure the distance between where your power supply will be and both sides of your pool where the amplifiers will be installed (see the setup and wiring illustration below). These distances will tell you how much 18-gauge wire you’ll need for connecting the amplifiers to power. Make sure to account for the distance of any dips or turns that the wires may take along their paths.

Lastly, measure the approximate distance that will be between your controller and where your strip lights begin. This distance will tell you how much 22-gauge wire you’ll need for connecting the controller to your strips. You will also need two small sections of this wire for connecting your first and second strip lights to the amplifiers.

2) Before you’re ready to install your LED strip lights, be sure to drain your pool. Begin by creating or locating a dry area away from your pool for the power supply. The power supply should be contained in a weatherproof box. Power supplies should be installed between a ground fault circuit interrupter (GFCI) protected circuit and the pool’s junction box. It’s crucial to use a GFCI protected circuit as it shuts off if current flows where it’s not supposed to.

Wire the included plug to the power supply, but do not connect to power until the installation is complete.

3) Connect your RGB LED controller to the power supply. Cut the barrel off of the controller wiring. Strip back the remaining wires, and connect its wires to the power supply.

4) Cut the LC2 connector off of the remaining end of the controller, and strip back the wires. Run 22-gauge four-conductor wire to connect the controller to your low-voltage pool lights; use dolphin connectors to join like-colored wires. Connect your first two LED strip lights to the controller by joining each set of like-colored wire with a dolphin connector. You should be connecting four wires of each color (red, blue, green, and black) together. For added protection, cover all wire connections in this installation with electrical tape.

5) You will apply strip 1 clockwise around your pool rim and strip 2 counterclockwise. If you have a flat surface, use mounting clips to secure the strips in place as you go. If you want to mount the strips under your pool rim, drill small holes in the trusses approximately every 2 feet. Use cable ties to anchor the strip to the truss. You can also use speed nuts or cotter pins for strip anchoring to avoid drilling holes.

Solder a small section of 22-gauge four-conductor wire onto the strip’s end terminals. To reseal the LED pool light strip, slide wires through the holes of a 10-mm end cap, fill the cap with silicone, and slide it into place on the end of the strip. Be sure to cover all of the exposed conductive traces to ensure water resistance. Allow a minimum of two to three hours for the sealant to cure.

7) Once the new end wires are attached to the strip, you will mount the amplifier. Use the double-sided 3M foam pad to mount the amplifier in the middle of strip 1 and strip 3. For best results and added security, apply 3M adhesion promoter to the amplifier and its installation location on the pool wall.

8) Using a dolphin connector, join each like-colored wire on strip 1 to the same color on one end of the amplifier. Do the same when connecting strip 3 to the other side of the amplifier. You should be connecting three wires in each color (red, blue, and green) together on each side of the amplifier. The black strip wire will be joined with white amplifier wire. Note that the separate group of just black and red wires are meant to be connected to the power supply. Follow the same instructions for connecting strips 2 and 4 to the amplifier on the other side of the pool.

9) Use 18-gauge wire and dolphin connectors to connect the amplifiers to your power supply.

10) Plug the power supply’s attached cord into an outlet, and enjoy your LED pool lighting system! Refill your pool with water, but make sure to leave space between the water line and the lights.

For more LED pool lighting options, see our entire selection of waterproof color-changing LED strip lights.

For technical questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

Do you know where your electric meter is located? Knowing how to find this piece of equipment AND how to read it are important for any home or building owner. Your electric meter reading provides you with information on your energy usage so that you can monitor it, helping you save energy and money. This also allows you to easily determine whether your monthly utility bill is accurate, so that you are not overspending unnecessarily.

It’s not difficult to learn how to read an electric meter. Most DC-area residences have one of two kinds of meters—a digital meter or an older model with a series of dials. Both types measure the kilowatt hours (kWh) that your household uses, which is also the measure used on your utility bill.

The secret to making sense of either type of meter is comparing the current reading with a prior reading or the number on your billing statement. Read the dials of older meters from left to right. There should be five dials. If the pointer on a dial is between numbers, choose the lower number. If the pointer looks to be exactly on a number, read the next lower number (unless the dial immediately to its right has passed zero). Digital meters are even simpler to read. The number displayed indicates the current usage.

To determine electric usage, take the reading from the previous day or month and subtract it from the current number. The difference will give you the amount of electricity your household used during that period. Any discrepancy between this figure and what’s on your energy bill is reason to take a second look.

If you have a question for your electric company, you’ll also want to tell them the meter number (usually located at the bottom of the meter).

Like any piece of electrical equipment, your electric meter should be handled (or NOT handled) with care. While it’s a good idea to monitor your electricity usage, it’s a bad idea to touch your meter. In fact, tampering with your electric meter is a crime in most areas. It’s also important to maintain clear access to your meter by keeping snow, trees, and bushes from obstructing view of the meter.

For more information on how to read an electric meter and how it can be helpful to you, call Kolb Electric. We can provide you with further tips to help you save on future electrical bills and install more efficient electrical systems, such as LED lighting, that will save you even more. We may also perform an infrared thermography inspection that helps to detect issues in your home, such as a roof leak or loose electrical connections, that are causing your heat to escape or your appliances to operate inefficiently.

Call now to schedule service if you’re located in Maryland, Virginia, or Washington, DC—877-287-1179877-287-1179. 

Outlets are seemingly innocuous parts of any home. They blend right into the walls and we hardly even know they are there. We often hide them with furniture or décor and never give them a second thought until we need to plug something in or unplug a device. It isn’t like we give them daily inspections or even monthly evaluations. Why would we? They do nothing. Or do they? Those outlets are not always as innocent as they may look. Sometimes, they are extremely dangerous and when you hide them, they can get away with a lot and you won’t know until it is too late. An electrician in Burbank wants you to be wary of those outlets and pay attention to any warn signs that indicate something may not be right. The team at The Electric Connection can give you more detailed information if you need it.

Burning wires have a very distinct, acrid smell. If you ever smell something a little off in the home and it seems like it is coming from a wall, you probably have a serious fire hazard explains a Burbank electrician. Plugging in and unplugging cords over and over puts stress on the tiny wires that give the outlet electricity. They can become loose. They touch each other or the insulation and slowly burn. This is how home fires are started. Other obvious signs of trouble are; *The outlet feels hot or the wall around the outlet feels hot

Don’t ignore your outlets says an electrician. Burbank homeowners need to call The Electric Connection right away if they suspect there is any trouble.