Aluminum LED profile housings allow you to create customized light fixtures with LED strip lights. Our Klus brand LED channels are available in many different styles, including recessed-, or flexible, O-shaped, and more. Available in 1- and 2-meter lengths, the channels can be easily cut for any application from under-cabinet lighting and bookshelf lighting to showcase lighting and transition strip lighting. They’re available with a variety of lens options, such as clear, frosted, and etched that complete the profiles. We’ve put together a step-by-step guide for using these channels to create your own light fixtures. Please note that your specific channel might vary from the one used in this tutorial.

Materials needed:

1. With a pair of clippers, carefully clip through the clear plastic heat shrink as shown in figures A-C. You will want to take your time and be careful not to cut the strip’s wires while removing it.

2. Lay the LED strip into the channel, and position it along the bottom so that the ends of the strip and the channel are lined up (fig. A). Now, remove the paper from the strip’s adhesive backing (fig. B), and adhere the strip to the LED channel—starting at the lined end and working your way to the other end of the strip. Be sure to leave roughly 1/4-inch free at the end of the channel so that you can install the end cap as shown in figure C.

3. If one of your end caps doesn’t come with a pre-drilled hole, you will need to drill your own to allow the wires of the LED strip light to come through. In this case, we used a Dremel tool, but other options are viable as well. Regardless of the tool you choose, it is helpful to mark the end cap where you would like the wires to come through. Start the hole small, and increase the size as necessary.

4. Place the end cap on the wired side of the strip by threading the wires through the end cap as shown in figure A. Insert the end cap into the end of the light bar, and push firmly until it is fully in place (fig. B).

5. On the open end of the bar, slightly peel up the end of the LED strip (fig. A); this is necessary to install the end cap. Now measure your channel lens, and trim off the excess with clippers (fig. B). Be careful when trimming to avoid cracking the plastic. Excess material can be lightly sanded off. Once the lens has been cut to the proper length, slide it into the channel, and install the end cap as shown in figures C and D.

6. That’s it! Your customized LED light fixture is complete and ready for installation, which we will cover in the next step.

7. Mounting this LED profile is as easy as applying double-sided tape to the back of it and sticking it to your intended surface. Be sure to cut the tape to fit the back of the LED profile and to leave the tape backing on the side not attached to the channel until you are ready to mount it.

For most LED profiles, mounting clips are available for a more permanent installation.

If you have questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

On average, over 350,000 home fires take place every year, claiming thousands of lives. How are your smoke detectors functioning? Don't make these mistakes with your smoke detectors:

Make sure your smoke detectors are installed correctly The U.S. Fire Administration recommends installing alarms both inside and outside sleeping areas. At a minimum, alarms should be located on all levels of your home, at least one near each sleeping area and preferably additional detectors in pathways between sleeping areas and exits out of your home. If you sleep with your bedroom door closed, smoke or use heat-producing appliances in or near your bedroom, or have noisy appliances in your bedroom that could block the sound of a smoke detector (TVs, stereos, air conditioners, and more), it is especially important to install one inside each bedroom. Always use a licensed electrician when installing hardwired smoke alarms. Alarms should be installed:

Smoke detectors save lives. Don’t fall victim to these common smoke detector problems or behind today’s recommended standards for protection. Contact Mr. Electric® today to ensure the proper installation and operation of these life-saving safety devices in your home.

What’s all the buzz about? Through smart-tech and general technology improvements, modern homes are getting safer and safer every year, which we can all be happy about. But that doesn’t mean we as homeowners should let our guard down! Electrical safety is still a big, big deal, and tons of fires are reported every year due to electrical failures or misuse. Some of the causes are even really odd, or something you might not expect. Do you know all of the dangers potentially lurking in your home?

At Kolb Electric, your safety and the electrical safety of your home is our absolute priority in all cases. Superior electrical service may be our pride, but safety will always come first and foremost! Today we’re here to talk about some hidden home threats, and what you can do to avoid them.

Looking for electrical services for your Bethesda home? Contact Kolb Electric today!

We all know that there are risks with say, outlets, or a damaged appliance. But there are plenty of problems that can come right out of the woodwork (sometimes literally!). Be aware of these potential problems, and prepare your home accordingly:

Need some trustworthy service from a certified electrician to shore up the defenses in your Maryland home? Contact Kolb Electric today! We’ve been putting the needs of our consumers first and foremost for nearly a century, and our experts are always ready to assist!

Becoming a licensed Colorado electrical contractor is not easy, and that’s the way it should be. Electrical systems—whether they are in a home or a large industrial facility—are both vital and potentially dangerous. Electricians need to be trained and skilled to ensure that these systems are installed correctly, functioning properly, and safely maintained; otherwise, serious problems may occur, which could lead to lost productivity or property. There are many companies who advertise electrical contracting services, but you don’t want your safety to be left in the hands of an amateur.

The Certification Process

There are three levels of licensure for electricians in the state of Colorado: residential wireman, journeyman electrician, and master electrician. Each level requires testing and many hours of verified on-the-job experience. In fact, the amount of time electricians must put in to be licensed may surprise you: *

PECI Goes Even Further

You Can Trust PECI

*from the Colorado Department of Regulatory Agencies