Modern day living is highly reliant on the use of electricity and the different appliances, equipment and fixtures it powers. Industries are even more reliant on electricity and their profitability is closely knit with how seamlessly their systems operate. They rely on electricity to such an extent that they rarely give it a second thought; well, at least not until something goes wrong such as:

Most of these problems can be attributed to poor power factor. Let’s understand a little more about what that is.

Power factor is essentially a measure of how effectively the incoming power is being used by the electrical equipment on your premises. It is expressed in terms of a numerical value in the range of 0-1. A higher power factor indicates that the electrical equipment is being used more effectively.

For instance, if the power factor is 0.8, it indicates that 80% of the power supply to the equipment is being utilised effectively and that 20% is being wasted. Regardless of what this ratio of effective usage Vs wastage is, the latter is an unnecessary expense. Typically, your power factor should be closer to 1; it indicates that your site is using energy in an efficient manner.

A number of businesses are currently being charged a kVA tariff and not a kilowatt tariff. This means, your service provider is probably charging you for the power they supply to you, rather than that you actually use. Simply put, you are paying for power that is being supplied to you, but which is being wasted. If your business has a low power factor, it means you pay even more for this waste. There is another aspect you should keep in view. As mentioned at the start, poor power factor has the potential to cause power drops and power losses; in turn, these lead to motor failure and overheating and failure of other equipment too.

Installation of Power Factor Correction equipment might just help avoid prohibitively expensive infrastructure upgrades; it does this by reducing the current electrical demand on your system & improving the efficiency stability. Based on which tariff you are on, power correction might just prove to be an excellent way for your business to deescalate its electricity costs.

The power factor can be improved by installing Capacitor Banks. These are PFC (Power Factor Correction) equipment and help correct the inefficiencies in the energy supply. Apart from this, they also reduce the peak demand on the power network. This is an effective and cost-effective solution to reduce your power bill as it helps lower the monthly demand and the capacity charges. Generally, the payback periods for PFC are between 1 and 3 years. Taking the life span of the PFC equipment into consideration & the potential savings, this investment can prove to be very worthwhile for you.

If you feel that you are paying too much for electricity, we at Allround Electrical can conduct a survey of the equipment used on your site and map their electrical consumption against the power your plant is using and is being charged for. We will then provide you a report of what your power factor is; and if it is low, how it can be corrected. For more information, call us at 1300 169 263. You can also drop us a line via email.

Thanks for reading,1300 169 263

Electricity is like a kitchen knife. If you use it wisely, it can cut food and prepare delicacies. If you use it unwisely, it can end up cutting your finger. Electricity flows through anything that is a “conductor.” Interestingly, humans are very good conductors of electricity!

Since electricity is a form of energy, a strong current has the ability to seriously harm you. If the current is strong enough, you can be fatally injured. Due to the strong possibility of a fatal injury occurring, electric cables are insulated. Another important reason why they are insulated is to prevent energy from dissipating into the surroundings, allowing it to be conserved.

We’ve recently added four new CAN Bus LED festoon bulbs. These 6418, 6451 festoon bulbs are designed to communicate with vehicle CAN Bus computer systems and prevent “bulb out” error messages. They can be used for numerous applications, such as map lights, dome lights, vanity lights, trunk lights, and footwell lights.

Powerful cool white LEDs are mounted to one side of the bulb’s printed circuit board for direct illumination without wasted light, and an LED-cooling heat sink is incorporated into the back of the board. These error-free bulbs are designed to last 25 times longer than incandescent bulbs.

FAQ post.

Hi Nick,

Mike and I just wanted to thank you and Rick for the excellent service yesterday, a Sunday during a major power outage at that.  From the time I placed the call for help to the time Rick walked out of our soon-to-be-warm-again home, it was only an unbelievable 1.5 hrs!!  I so appreciate your ‘straight-shooting’ with me on the phone about whether our problem could be Oncor related or in our wiring and the option to switch our dead furnace thermostat to the one working leg of power we seemed to have.  Rick arrived just when he said he would, went right to work and determined that we were indeed receiving full power from Oncor, but one of our breakers was bad.  He replaced it, checked things out and was on his way.

You have impressed us with your quality of service.  We certainly will use you again and recommend you when someone asks if we know a good electrician….we do now!