Did you know that proper surge protection could help avoid short circuits and fire hazards?  In fact, using up-to-date surge protectors (suppressors) for your appliances, or even your entire house, could save you thousands of dollars in property damage. These are just a few reasons why surge protection should be of the utmost importance for you and your home this holiday season.

What are power surges?

First, before diving deeper into the different advantages of protecting your home against power surges, it’s important to understand what electrical surges are, and why they’re such a concern. An electrical surge, also known as a “voltage surge”, is an electrical disturbance that can be caused by a variety of spikes in voltage. More specifically, these surges are usually caused by lightning strikes, power outages, short circuits, or tripped circuit breakers. Problems occur when these short spikes in electrical power overload circuits in home appliances and other electronics.

Why is it so important to protect your home against power surges?

For starters, power surges can be very dangerous for you, your family, and your house. Surges are one of the most common causes of house fires, usually resulting from a combination of faulty wiring and irresponsible electronics hook-up by homeowners. This is especially apparent around the holidays.

Aluminum LED profile housings allow you to create customized light fixtures with LED strip lights. Our Klus brand LED channels are available in many different styles, including recessed-, or flexible, O-shaped, and more. Available in 1- and 2-meter lengths, the channels can be easily cut for any application from under-cabinet lighting and bookshelf lighting to showcase lighting and transition strip lighting. They’re available with a variety of lens options, such as clear, frosted, and etched that complete the profiles. We’ve put together a step-by-step guide for using these channels to create your own light fixtures. Please note that your specific channel might vary from the one used in this tutorial.

Materials needed:

1. With a pair of clippers, carefully clip through the clear plastic heat shrink as shown in figures A-C. You will want to take your time and be careful not to cut the strip’s wires while removing it.

2. Lay the LED strip into the channel, and position it along the bottom so that the ends of the strip and the channel are lined up (fig. A). Now, remove the paper from the strip’s adhesive backing (fig. B), and adhere the strip to the LED channel—starting at the lined end and working your way to the other end of the strip. Be sure to leave roughly 1/4-inch free at the end of the channel so that you can install the end cap as shown in figure C.

3. If one of your end caps doesn’t come with a pre-drilled hole, you will need to drill your own to allow the wires of the LED strip light to come through. In this case, we used a Dremel tool, but other options are viable as well. Regardless of the tool you choose, it is helpful to mark the end cap where you would like the wires to come through. Start the hole small, and increase the size as necessary.

4. Place the end cap on the wired side of the strip by threading the wires through the end cap as shown in figure A. Insert the end cap into the end of the light bar, and push firmly until it is fully in place (fig. B).

5. On the open end of the bar, slightly peel up the end of the LED strip (fig. A); this is necessary to install the end cap. Now measure your channel lens, and trim off the excess with clippers (fig. B). Be careful when trimming to avoid cracking the plastic. Excess material can be lightly sanded off. Once the lens has been cut to the proper length, slide it into the channel, and install the end cap as shown in figures C and D.

6. That’s it! Your customized LED light fixture is complete and ready for installation, which we will cover in the next step.

7. Mounting this LED profile is as easy as applying double-sided tape to the back of it and sticking it to your intended surface. Be sure to cut the tape to fit the back of the LED profile and to leave the tape backing on the side not attached to the channel until you are ready to mount it.

For most LED profiles, mounting clips are available for a more permanent installation.

If you have questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

emergency power systems in preventing the loss of electricity to data sources and other IT operations such as servers, point of sale systems, PC’s, routers, switches, telecommunications, and other equipment. The Indoor Generator offers IT professionals an affordable solution that provides hours of backup power at a fraction of the cost of current UPS products on the market. For more information on the www.electricmaninc.com.

Capitol Lighting created a friendly competition challenging local designers to create one-of-a-kind bathroom spaces and put a call out to all Northern New Jersey-area interior designers to participate. Two top designers were chosen out of numerous applicants to compete in the unique challenge of remodeling the men’s and women’s bathrooms at the company’s Paramus showroom — one of which will be crowned the “Thronedown” champion. The finalists were chosen based on previous work and have been given a $2,000 project budget with lighting supplied by Quoizel and Feiss.

Anna Maria Mannarino- Mannarino Designs, Inc.