If you’re dying to install your new instructions for how to install a light bar. These instructions include options for installations with or without a wire harness and for connecting to existing LED lights. Installation will vary based on the type of vehicle, existing lighting setup, and chosen wiring method, but these instructions can serve to give you a general idea of the process. Light bar mounting instructions are also available and are listed by WH-DTS10, WWH-DTD30; (ATP) WH-ATPD20, sdoptional mounting brackets; be sure not to overtighten the hardware (you will need to adjust it in step 7).

3. Route the lighting side of the wiring harness from the battery to the light in a safe, secure manner. Connect the harness to the light. Be sure to avoid heat sources and any moving parts while running your wires. Prolonged chafing of the wires may lead to a short in the circuit. Typically, following the vehicle manufacturer’s wiring harness is a safe path to follow. Some lights may not have DT or ATP connections on them, but the connectors can be added from the harness kit or purchased separately (ATP-FPT).

4. Continue to route the switch portion of the harness to the desired location of the switch. The switch may need to be unplugged from the harness to make routing of the harness easier. An optional remote-controlled switch (RS-x) are also available with different legends.

5. Connect the black (ground) wire with the large ring terminal from the harness to the negative battery terminal. Connect the red (power) wire with the large ring terminal from the harness to the positive battery terminal.

6. Secure the relay to a suitable location, and test the light to make sure the circuit works.

7. Finally, aim the light in the desired direction, and tighten all mounting hardware.

3. Connect the black ground wire of the new light to the ground wire of the old light with solder and heat shrink tubing (PSC-x). Connect the red power wire of the new light to the power wire of the old light.

4. If the new LED work light or off-road light bar has an ATP or DT connector that you wish to utilize, corresponding ATP (DT-MPT) pigtails are available.

5. Finally, aim the lights in the proper direction, and tighten all mounting hardware.

1. Find a suitable mounting location that will allow for running wires and mounting the LED light bar. Mark where your holes will be for the light bar brackets or mounting feet. Check behind drilling locations to ensure nothing will be damaged. Drill appropriate-sized holes.

2. Mount the lights with the provided hardware or with DT-MPT or RRS-SP, RRS-SPx, or RCS-RF25A) under your hood to speed up install time and avoid routing wires through your vehicle’s firewall. Route another run of red wire from the pigtail adapter (connected to the light) to the output terminal of the switch. Be sure to avoid heat sources and any moving parts while running your wires. Prolonged chafing of the wires may lead to a short in the circuit. Typically, following the vehicle manufacturer’s wire harness is a safe path to follow.

4. Be sure to double-check for all obstructions and proper clearance. Drill an appropriate sized hole for the switch, and mount it.

5. Connect your black wire to the negative battery terminal. Connect your red wire to the switch input terminal and to the positive battery terminal with an appropriate-sized fuse holder (MAF-x) installed within 18 inches of the battery. You will have to cut your section of red wire to allow for the fuse holder to be installed between the switch and battery. Connect your other run of red wire to the switch output terminal.

6. Finally, aim the lights in the proper direction and tighten all mounting hardware.

When you own a home, it’s easy for household expenses to spiral out of control. Every year, the average homeowner is in the unenviable position of spending thousands of dollars on owning and maintaining a home- and that’s just when everything is going well! If an emergency hits, many homeowners have to make sacrifices they can ill afford just to keep the home up and running. The best strategy to avoid disaster is to work on cutting down the everyday household expenses associated with owning a home.

So where does the money really go? On average, American homeowners spend about 34 percent of their income on home expenses. Paying for the house itself, of course, is the largest chunk of that expenditure, but does it surprise you to know that utilities make up the next largest amount? Most Americans spend about seven percent of their income on utilities; that’s more than what they spend on entertainment, clothing for the family and even health care! Obviously, that’s an area where it makes sense to find ways to scale back. If you live in Texas, it’s even more important than it is for people in other states as Texas electricity rates are 30 percent higher than rates elsewhere.

To save money on electricity, you need to understand it. Electric companies measure energy usage in kWh, which is a measurement of the hours you spend using 1000 watts. By lowering your kWh, you will, of course, lower your electricity cost, but where do all those kilowatt-hours go? Appliances can be huge energy hogs but so can game systems, televisions and computers. Older homes are often ill-equipped to handle the energy demands of a modern lifestyle, and this can be not only costly but dangerous, as faulty electrical systems can lead to house fires. Modernizing your home can save on more than just household expenses- it might also save your life.

Fortunately, there are some easy ways to save on energy (and its associated costs). If your home is more than 20 years old, get your electrical system checked out by a professional to determine if you need any upgrades. Buy ENERGY STAR compliant appliances whenever possible, and turn off anything you’re not using, from lights and appliances to your Xbox 360.

Are you ready to lower your household expenses? It helps to find a company such as ElectricMan, committed to providing low-cost electrical services without sacrificing high-quality service. A family owned business, we offer quality electrical services, and we only employ professional, licensed, certified electricians. And we’re available 24 hours a day, 7 days a week. Whether it’s a general electrical repair or an electrical emergency, ElectricMan has you covered! Visit the ElectricMan website to learn more, or connect with our online community on Facebook, Twitter, Pinterest and Google Plus.