These systems are still expensive compared to the conventional electric generating plants such as hydro. And since they only generate power during the day, batteries or other storage systems are required to ensure power availability during the night or times when the conversion is low. This means spending more on batteries, which are currently the most popular storage devices.

Another limitation is the intermittent nature of light, making the energy unsuitable for some applications.

Space limitations may influence the maximum power that a consumer can generate. The cheaper panels have a lower conversion rate and require larger areas. However, customers may overcome this by using the more expensive but higher efficiency panels which require less space.

Improved photovoltaic technology, mass production and lower installation costs have seen the cost of photovoltaic systems and components such as batteries fall rapidly. Incentives such as financing, rebates, and wide acceptance by homeowners have influenced the use of the photovoltaic cells.

From the 1950s to the 1980s, the Federal Pacific Electrical Company (FPE) installed electrical panels in millions of homes across the country. Unfortunately, these electrical panels are basically recipes for disaster—over the years, electricians and home inspectors have found that FPE panels often fail to protect homes from overcurrent or short circuits. The danger seems to happen randomly: even if panels have been installed and working properly for years, a single incident can quickly cause the panel to overheat and create a major fire hazard.

Remember—circuit panels trip in response to unusual surges of electricity. If they fail to trip, as FPE panels often do, those electrical surges cannot be stopped or shut off manually and will move through your home until they run out of fuel or until the wires burn out. This could cause the panel to overheat and catch fire, leading to a potentially serious disaster.

FPE panels may not be up to modern safety codes – electrical safety standards have been updated significantly since the 1980s, and experts say that FPE panels, which were produced from the 50s and into the 80s, do not meet these updated standards. Some of the deficiencies noted by home inspectors include:

FPE panels may have serious design flaws – not only do FPE panels not meet modern safety standards, but they also came with some serious design flaws that weren’t even common among panels built around the same time. Some of the most significant flaws include:

FPE panels may have manufacturing defects – as if that weren’t enough, the Consumer Product Safety Commission (CPSC) has noted a number of defects that make FPE panels unfit for homes, including weak materials used to construct the breakers that may prevent them from tripping and could cause the panel to catch fire.

If you live in an older home and you’re worried your panel might be a danger, call Kolb Electric. Our trained electricians are familiar with the potential hazards of FPE and other outdated panels and can replace your existing panel with a modern panel that will keep your home safe for decades.

For more information about circuit panel replacement in Maryland, Virginia, or Washington, DC, call Kolb Electric today.

Your business operations are probably reliant upon electricity, like most operations in the modern world of today.  Do you have a backup plan in case the power goes out?  Most other businesses will simply shut their doors and deal with the consequences when the power is restored, but you can maintain business as usual thanks to the innovation of Dallas electrician to install an Indoor GeneratorTM for your business could be incredibly beneficial.  For certification or insurance reasons, you may have an even greater need to remain up and running.  Your valuable computer or medical equipment will thank you when you save them from the devastation of power surges and outages.

Consider these benefits of having backup power systems installed in your business:

A safety switch is essentially a device that very quickly switches-off the electricity in case any electrical fault is detected. In effect, it reduces the risk of injury & death caused by contact with electricity. Current day safety switches are very different from the ones used even up until a decade ago. Today, it’s mandatory to have these installed in buildings where any kind of electrical addition or upgrade has taken place.

Apart from this, safety switches are also needed for power outlets that that supply electricity to mobile homes like caravans etc. It’s not mandatory to have these safety switches in older homes; however, the recommendation is that you should consider getting them installed. It is one of the most effective ways to protect your family & yourself from electric shock.

ELCBs or Earth-leakage circuit breakers are safety devices used to prevent shock in electrical fixtures which have high Earth impedance. The current installations use the circuit breakers that directly detect leakage in current. Here are some features of an ELCB:

RCDs or RCCBs are essentially modern electrical wiring devices which quickly disconnect a circuit if they detect that there is an imbalance in the current between the energized conductor/s & the return conductor. They are designed to immediately switch-off the electricity supply when the electricity leaking to earth is detected to be at harmful levels. These devices offer very high levels of protection from electric shock.

Voltage Earth-leakage circuit breakers were first introduced around 60 years ago, while the current ELCBs were launched only around 40 years ago. For a very long time, voltage-operated ELCBs & differential current-operated ELCBs were both called ELCBs; this was because it was a far easier term to remember. However, as expected, this common name caused a significant amount of confusion within the electrical industry.

If someone accidently used the wrong one in a particular application, the installations may not get the kind of protection it needed. It was to eliminate this confusion that the International Electrotechnical Commission decided that the differential current-operated ELCBs will be termed as RCD (residual current devices). Any current that’s over & above the load current is referred to as the residual current.

ELCBs have a number of disadvantages such as:

Today the RCD is preferred means of providing effective shock protection. The term is also most widely used across the globe.

For more information about RCDs and the best electrical solutions, call Allround Electrical at 1300 169 263. You can also write to us at this email address. You may also reach us through this online contact form.

Thanks for reading,1300 169 263

There are some jobs out there that you can very well do all on your own. But there are others that need the guidance and experience of a certified electrician in Gaithersburg. Considering a renovation or remodel for your home and not sure what you’ll need an expert for? Follow along with the team at Kolb Electric to find out!

It can be tempting to try your hand at electrical work, particularly if you think a job is simple. But at Kolb, our team would really, really recommend that you almost never attempt electrical work on your own.

Why? Primarily because of safety. It can be very easy to get an injury when doing electrical work, even for a professional. But also because a lot of work requires certain certification for the job to be within electrical code, which is a legal matter you don’t want to be on the wrong side of.

Here are our top “this needs an expert” picks:

Planning on doing a remodel and need the experience and skill of a certified electrician in Gaithersburg? We’re the team for you! Our experts are top-class when it comes to comprehensive electrical service, and we’re always happy to help. Contact us today to find out more about our services, or to plan your remodel with our electrical professionals!