By: Emilie Sims

Electrical outlets are found in nearly every room of the home, which represents a constant risk if you have small children. According to the National Fire Protection Agency, approximately 2,400 children each year suffer severe shocks and burns from inserting objects into the slots of electrical outlets. Additionally, there are an estimated six to 12 child fatalities each year related to this. Prevent this from happening to your family by childproofing the electrical outlets in each room of your home.

Also known as safe plates, these are additional covers that sit on top of your existing outlet and are held in place by a screw. There is a spring-loaded plastic cover that prevents your child from poking anything inside of the outlet.

Installing tamper resistant receptacles (TRRs) around the home provides a permanent solution to help reduce the risk of childhood shock and injury. TRRs, which look like ordinary outlets, are designed with small, spring-loaded receptacle plates that close off the slots, but open when equal pressure is applied to both sides. This design prevents children from inserting fingers or other foreign objects into the slots, and reduces risk of electrical shock or injury.

There are also several types of childproof electrical outlets that you can choose to install that will provide a permanent way to reduce risk of child injury.

This tamper-resistant outlet contains both a switch and an outlet to plug in devices. The dual mechanical shutter system blocks the insertion of objects into the outlet, increasing your child’s safety.

A ground fault circuit interrupter (GFCI) outlet can be identified by the “test” and “reset” buttons located on the receptacle. A GFCI outlet helps protect you from electrical hazards by shutting off the electricity circuit when it detects an imbalance. The National Electrical Code requires these outlets to be installed in water susceptible areas, such as the kitchen and bathroom. Test these outlets once a month to ensure they are working properly.

These receptacles look similar to standard ones, but the two outlets have the ability to spin 360 degrees. These outlets also allow you to use two large plugs at once.

Visit the Electrical Safety Foundation International and the National Fire Protection Association for more information on keeping your family safe around electrical outlets.

CCT indicates the hue and tone of white light emitted from a specific bulb or fixture. It’s measured in Kelvins (K), which is similar to degrees in Celsius. Different temperatures on the Kelvin scale represent different colors. For example, light at 2000K-3500K looks more orange/yellow and is called ultra warm or warm white, and as temperature increases in Kelvins, color changes to more of a “paper white” known as natural or neutral white (between 3500K and 5100K) and finally into a bluish-white known as cool white (5100K+).

As a light source’s color temperature increases, brightness often increases. While shopping for LED lights, pay close attention to the color temperatures that are available for any one bulb or fixture. Choosing a warm white bulb with a color temperature around 3000K might mean sacrificing some brightness. Whereas, if you choose the natural white version, it’s likely that it will have a higher output.

Any room can benefit from light strip, globe bulb,

In order to understand nanometers, you must first understand the electromagnetic spectrum and wavelengths. The electromagnetic spectrum is the entire range of invisible and visible light, and a wavelength is the distance between peaks of light waves. Wavelengths are measured in nanometers, which are simply units of length that indicate colors of light within the spectrum. Nanometers will tell you how red, green, yellow, purple, etc. a light source really is. These measurements start lower at ultraviolet and increase from green to blue, yellow, orange, and then red. The wavelength of a colored light can be found in the light’s specifications table.

MR16 beam angle in degrees (left to right): 36, 24, 15

Fixtures or bulbs that emit wide beams, such as BR LED bulbs for can lights are great for areas that require a lot of light, such as basements, kitchens, or living rooms. Narrow beam angles like those from can lights with MR LED bulbs are best for highlighting decor or small areas. Globe bulbs, such as G30 LED vanity bulbs, have 360-degree beam angles, which means that they throw light in all directions. Globe bulbs are the perfect choice for centralized light fixtures.

There are times when you simply can’t or shouldn’t do certain repairs around your house. Not everybody is trained or cut out to take care of all the little jobs that arise. You need to hire a professional from time to time. One of the professionals you will likely need on occasion is a Glendale electrician. If you have never used an electrician or have had a bad experience in the past and are looking for a new one, how do you know what to look for? The team at The Electric Connection has been helping folks out for years and is here to help you as well. The following characteristics are what you should look for when you need to hire an electrician to take care of work around your home.

• Good reputation-ask your friends, neighbors and family members if they have used a particular company. What was their experience? Do some checking online as well. Angie’s List is a great place to start.

• Professional-an electrician that shows up at your door should look and act professional. A clean uniform is a good sign of a professional contractor. If you are bringing an electrician into your business, a professional appearance is very important.

• Licensed and bonded-this is an absolute must when hiring an electrician. Glendale residents should only allow contractors into their homes or businesses who have the proper licensing through the state as well as a bond to protect you in case there is any damage done to your home.

• Timely-Cable companies are often joked about because of their lack of timeliness, but it isn’t a laughing matter. You are busy and don’t have hours to sit around waiting for an electrician to show up. You need a company that can give you a set window and stick to it.

If you need an electrician, you can call The Electric Connection and find an electrician who meets all of these standards.