Click To Tweet

This issue almost exclusively applies to instructions on how to safely repair it.

The average rated life of a light bulb represents how long it took for half of the bulbs to fail during testing (given perfect conditions). If your bulb lasted 12,315 hours (you counted!) but the label touted an average rated of life of 20,000 hours, you’re actually still within range of an acceptable life span.

We measure LED bulbs a bit differently since they never technically burn out, but rather fade over time. Instead, the Lighting FactsTM label indicates LED lumen maintenance (LM), which is an estimate of the bulb’s lumen depreciation over a given time.

Solution: Understand that the expected lifespan of your light bulb is simply an estimate based on testing that was performed in a controlled environment. When a bulb burns out earlier than that estimate, it doesn’t always mean something is wrong with it.

GFCIs or ground fault circuit interrupters are safety devices that have been extremely effective in reducing the total number of home electrocutions by almost 50%, in Australia. Most new homes and businesses now have these devices installed in locations where water is present in and around the premises. It’s important that electrical installations in outdoor locations be protected from wind and rain; that’s the one way to prevent shock hazards.

Before we understand what a GFCI is, let’s understand what a ground fault is. It is the unintentional flow of electrical current between the source and any grounded surface. If the electrical installation isn’t properly protected, an individual that comes into contact with an energised part can suffer an electrical shock.

For instance, if the person is holding any deteriorated electrical cord attached to the hair dryer, and it happens to touch a plumbing fixture they are using, they can get electrocuted and will suffer a painful shock.

This small receptacle has “test” & “retest” buttons on it. It may sometimes be built into circuit breakers that are installed in the main electrical panels. When electricians are conducting an electrical audit, they also test whether the GFCIs are functioning properly. They might also recommend that you get GFCIs installed in the vicinity of plumbing fixtures.

These are extremely useful electrical safety devices which trip the electrical circuits in case they detect any leakage current or ground fault. An individual that’s become the pathway for a leaked current can get a severe shock or will get electrocuted. It is important to get GFCIs installed in any outdoor or indoor areas where you feel that water might come in contact with the electrical installations or fixtures you have on your property.

Ideally, the areas where GFCIs should be installed include:

It is important that these devices be checked with regularity. If you have opted for an electrical maintenance contract, the electricians will ensure that the GFCIs are checked along with all the other installations; this will help confirm they are working as they should and that they provide the necessary safety to those living or working on your premises. You can also test the GFCIs on your property, by following these basic steps:

If you aren’t too sure about whether you have GFCIs installed at the right points on your property, call in your local electrician. They will inspect all the fixtures and inform you if GFCIs have to be installed in any specific rooms or outdoor spaces. Aside from this, they will also audit the rest of the installations and tell you if any upgrades are required.

However, choosing a ceiling fan can be a sometimes difficult endeavor. Knowing what size fan would fit your room, the ideal style, what type of lighting you’ll need, the features the fan contains and staying within your budget can all be a bit of a challenge. We understand that it can be a challenge, so 1800Lighting is here to help; this is the ultimate buyer’s guide for selecting the perfect ceiling fan for almost any need.

In case there is a flash flood or storm in your area or if there is a severe plumbing leak or pipe burst, that can result in flooding of water in different areas of your home. Water can cause a lot of damage to the installations and features on your property, and you would have to start the clean-up and repairs without delay. This is also when you start evaluating what can be salvaged and what would have to be replaced – and this includes your home’s wiring.

The wiring inside the walls can become dysfunctional and dangerous if it’s exposed to or submerged in water. If there is a severe flood, it becomes important to completely replace the wiring in your home. Not too many builders actually use wiring that’s rated for water exposure of this kind. Of course, not much can be done till the time all the flood water recedes and all the water has been cleared out from your home.

Even when all the water is pumped out from the indoor spaces, it’s best to shut down the electricity supply at the circuit box mains before continuing with anything. Call in your local electrician to test the wiring in your home. Even if it is still in a working condition, it’s never a good idea to use it.

The insulation can get degraded and that can raise the chances of an electrical fire in the future. In addition, when there are traces of moisture in the wiring, that leads to mould & mildew growth and the metal parts in the system can corrode. This is especially the case when the property has become flooded with salty water.

When it comes to rewiring jobs, you also have to factor in the cost of opening up the wall panels and fixing them. In instances of a flood, the walls are generally torn down right up to the framework. If you take this opportunity to upgrade the wiring in your home, you can save a significant amount of money.

Floodwater is never clean and that proves to be an additional hazard to the wiring and other installations in your home. Chemicals, oil, sewage and a number of other contaminants that come with the floodwater work their way into the smallest spaces, and this is why it’s best to just start afresh with the installation. In comparison, if your home’s wiring has been impacted by water from a burst pipe, you might be able to save these features; this is because it may not be fully-submerged in water.

However, it’s never a good idea to test the condition of the wiring yourself and you should call in a skilled and licensed electrician to thoroughly check and evaluate the installation and give their opinion. Regardless of whether the wiring in your home has got impacted by flood water or water from a damaged plumbing installation, it’s important to get it checked without delay. The professionals will provide suitable solutions based on the condition and location of the wiring.