Custom Electrical Services was recently voted for first place for Urbandale and Johnston area as best electrician!  The pole was taken by USA Today Best, and was presented by the Des Moines Register.  The voting is segmented into different areas by city.  Not all areas have the polls closed as of date.  The Urbandale and Johnston closed on September 27th, 2016.  The Des Moines metro voting closes on October 11th, 2016.  Custom Electrical Services would like to thank all the Urbandale and Johnston residence who took the time to vote.  We are proud to serve the Urbandale and Johnston area 24 / 7 as well as all of central Iowa!

We take pride in our work.  Our track record supports this.  Our electricians are not only licensed.  They receive special training that gives them superior customer service skills compared to other electricians.  We work hard to provide the best customer service experience possible.  Our electricians understand that your home is your castle.  They show respect for you and your property.  We are not your typical electrician that comes out and says your project is going to cost X.  We take the time to evaluate your entire electrical system as well as perform our full page safety inspection.  This provides a TON of added value to our service.  When is the last time someone took your panel cover off and inspected all your connections?  Most customers say not since I have lived here!  Electrical connections can loosen over time.  Wiring can expand and retract as loads fluctuate on the circuits, this expansion and loosen the connections inside your panel or breaker box.  Loose connections can leave to excessive arching and can cause fires.

Who are you letting into your home?  Our electricians receive an extensive background check.  We are not going to send a criminal into your home.  We realize the delicate nature of having strangers come into your home.  While you may not personally know the electrician you can rest assured we do!  Our background checked electricians are team members, not sub contractors.  We employee them full time and work one on one with them on a daily basis.  We work with them to develop the best customer experience possible.  We want you to feel comfortable with having our trained service technician in your home so you can be just as comfortable as we are with them.

In addition to a 3rd party background check our electricians receive drug testing.  You would not a person on drugs drive your kids to school!  So you defiantly don’t want an electrician on drugs performing wiring in your home!  Are drug tested and background checked electricians were the seal of safety.  This seal is worn with pride and taken very seriously.  When you see the seal of safety on our electricians uniform you know that you are working with a safe professional.

RGB LED strip lights are a great way to add a pop of color to your above-ground pool. These low-voltage LED lights can be applied to the inside rim of your pool or around your pool deck. With RGB LED strip lights, you can choose from a ton of dynamic color-changing and single-color modes with adjustable brightness and speed control. They’re great for parties or late-night swims and can be easily installed. We’ve included installation instructions for our waterproof LED strip lights. Some cities require above-ground pool lighting to meet National Electrical Code (NEC) Article 680 standards, which would limit possible pool lighting installation locations. Before you purchase LED pool lights, check your city’s code requirements. We also recommend that you have a certified electrician install your lights.

1) Before ordering your LED strip lights, measure the diameter of your pool and multiply by 3.14 to find its circumference; this number indicates the total length of strip that you will need. The 21-foot pool used for these installation instructions has a circumference of 65.94 feet and requires 4 runs of 16-foot LED strips.

You will also need to measure the distance between where your power supply will be and both sides of your pool where the amplifiers will be installed (see the setup and wiring illustration below). These distances will tell you how much 18-gauge wire you’ll need for connecting the amplifiers to power. Make sure to account for the distance of any dips or turns that the wires may take along their paths.

Lastly, measure the approximate distance that will be between your controller and where your strip lights begin. This distance will tell you how much 22-gauge wire you’ll need for connecting the controller to your strips. You will also need two small sections of this wire for connecting your first and second strip lights to the amplifiers.

2) Before you’re ready to install your LED strip lights, be sure to drain your pool. Begin by creating or locating a dry area away from your pool for the power supply. The power supply should be contained in a weatherproof box. Power supplies should be installed between a ground fault circuit interrupter (GFCI) protected circuit and the pool’s junction box. It’s crucial to use a GFCI protected circuit as it shuts off if current flows where it’s not supposed to.

Wire the included plug to the power supply, but do not connect to power until the installation is complete.

3) Connect your RGB LED controller to the power supply. Cut the barrel off of the controller wiring. Strip back the remaining wires, and connect its wires to the power supply.

4) Cut the LC2 connector off of the remaining end of the controller, and strip back the wires. Run 22-gauge four-conductor wire to connect the controller to your low-voltage pool lights; use dolphin connectors to join like-colored wires. Connect your first two LED strip lights to the controller by joining each set of like-colored wire with a dolphin connector. You should be connecting four wires of each color (red, blue, green, and black) together. For added protection, cover all wire connections in this installation with electrical tape.

5) You will apply strip 1 clockwise around your pool rim and strip 2 counterclockwise. If you have a flat surface, use mounting clips to secure the strips in place as you go. If you want to mount the strips under your pool rim, drill small holes in the trusses approximately every 2 feet. Use cable ties to anchor the strip to the truss. You can also use speed nuts or cotter pins for strip anchoring to avoid drilling holes.

Solder a small section of 22-gauge four-conductor wire onto the strip’s end terminals. To reseal the LED pool light strip, slide wires through the holes of a 10-mm end cap, fill the cap with silicone, and slide it into place on the end of the strip. Be sure to cover all of the exposed conductive traces to ensure water resistance. Allow a minimum of two to three hours for the sealant to cure.

7) Once the new end wires are attached to the strip, you will mount the amplifier. Use the double-sided 3M foam pad to mount the amplifier in the middle of strip 1 and strip 3. For best results and added security, apply 3M adhesion promoter to the amplifier and its installation location on the pool wall.

8) Using a dolphin connector, join each like-colored wire on strip 1 to the same color on one end of the amplifier. Do the same when connecting strip 3 to the other side of the amplifier. You should be connecting three wires in each color (red, blue, and green) together on each side of the amplifier. The black strip wire will be joined with white amplifier wire. Note that the separate group of just black and red wires are meant to be connected to the power supply. Follow the same instructions for connecting strips 2 and 4 to the amplifier on the other side of the pool.

9) Use 18-gauge wire and dolphin connectors to connect the amplifiers to your power supply.

10) Plug the power supply’s attached cord into an outlet, and enjoy your LED pool lighting system! Refill your pool with water, but make sure to leave space between the water line and the lights.

For more LED pool lighting options, see our entire selection of waterproof color-changing LED strip lights.

For technical questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.