Let’s face it—halogen and incandescent headlight bulbs are a thing of the past. fanless, driverless LED headlight bulbs were used in this installation.

If your vehicle allows for horizontal adjustments, mark the distance between your headlight centers with two vertical lines of tape. These lines are important for projector headlights and/or lining up beam cutoff points. Repeat these tape lines for your other headlight.

6. Remove your headlight assembly if necessary, remove the current bulbs, and install your new LED bulbs. Check your owner’s manual for specific instructions on how to replace your headlight bulbs.

7. Depending on your vehicle, you may have to adjust your headlight beam before or after the assembly has been reinstalled. Your owner’s manual will explain how to adjust the beams. Align each headlight so that the top edge of the beam is at the same height as your horizontal line(s). If your headlights can be adjusted horizontally or produce two light cutoff points, use the vertical tape lines to align them properly.

3. Shake the vehicle to ensure that your suspension system is settled. For more precise adjustments, inflate all tires to their designated psi capacity and have someone sit in the driver’s seat. Also, make sure that your vehicle’s gas tank is at least half full.

4. Measure from the ground to the center of your headlight assembly where the bulb is located. This step must be done for all vehicles. If your vehicle allows for horizontal headlight adjustments in addition to vertical adjustments, it’s important that you also measure the distance between the centers of both headlight bulbs. The vehicle featured in this video allows for vertical headlight adjustments only; therefore, center lines aren’t necessary but are shown for demonstration purposes.

5. Turn on your low-beam headlights. Using painter’s tape, mark your headlight measurements on a flat wall. Measure from the ground up, and apply a horizontal line of tape to the wall; this line represents the top of your headlight beam. You can either apply one long, continuous line or small sections where the brightest areas of the headlight beams are shown.

If your vehicle allows for horizontal adjustments, mark the distance between your headlight centers with two vertical lines of tape. These lines are important for projector headlights and/or lining up beam cutoff points.

Have you noticed a sudden spike in your electric bill? Or has your bill gradually increased month-over-month? Whatever the problem you’re facing, an increase in electricity costs is never fun—so we want to help you make sure you’re doing everything you can to keep your electric bill as low as possible. Most families waste energy in a number of ways, ways that are easy to stop, given a little awareness.

At Kolb Electric, we don’t want you to pay any more than necessary on your electric bills. Our experienced, fully licensed electricians can help you make smart decisions about your electrical usage so you can keep your utility bills down. After all, we’ve been helping Maryland, Northern Virginia, and Washington, DC home and building owners with their electrical needs for more than 90 years. We know a thing or two about what we’re talking about! For tips to help you save on your electric bill and/or to set up an appointment for your home or building, give us a call at 877 287-1179.

LED Tubes and LED Panels become the best solution for the office workplace environment. They are cost effective lighting solutions, provide good lighting quality, last longer and contain or emit no harmful compounds while leaving an ecological footprint in each building. This article is going to explain the difference between tube fixtures and panel fixtures. They are both different, but often times get mixed up when talked about. Let’s clarify any confusions you may have about the two fixtures…

LED Panels are installed in dropped paneled ceilings. perfect replacement for expensive shatterproof fluorescent lamps. MyLEDLightingGuide LED tubes do not contain glass and will not shatter if dropped. Fluorescent tubes contain mercury, some projects decide for LED versions because they want to remove mercury out of the building.

All LED tubes use drivers that power the LEDs. The ballast is converting the AC power from the utility company into LED’s DC power. Some manufacturers incorporate the drivers in the LED tubes. Some decide to use an external driver outside of the tube. There are some subtle differences between the two designs. Retrofitting to LED tubes with internal drivers involves removing the ballast and rewiring the line source. Retrofitting external driver tubes involves removing the ballast, the line source gets wired to the external LED driver that is connected to the tubes. More and more people ask for LED tubes that can be just installed as a plug and play version into existing fixtures without removing or rewiring the existing ballast. While the installation of these tubes is simple, they are compatible with most ballast, but not all ballasts. Contact the lighting experts at MyLEDLightingGuide.com to ensure the tubes will run properly.

Changing the light at work and in offices is easily done by LED tubes. They are readily set up and use considerably less power. LED tube light sources offer smooth, stable and clear lighting conditions.