Aluminum LED profile housings allow you to create customized light fixtures with LED strip lights. Our Klus brand LED channels are available in many different styles, including recessed-, or flexible, O-shaped, and more. Available in 1- and 2-meter lengths, the channels can be easily cut for any application from under-cabinet lighting and bookshelf lighting to showcase lighting and transition strip lighting. They’re available with a variety of lens options, such as clear, frosted, and etched that complete the profiles. We’ve put together a step-by-step guide for using these channels to create your own light fixtures. Please note that your specific channel might vary from the one used in this tutorial.

Materials needed:

1. With a pair of clippers, carefully clip through the clear plastic heat shrink as shown in figures A-C. You will want to take your time and be careful not to cut the strip’s wires while removing it.

2. Lay the LED strip into the channel, and position it along the bottom so that the ends of the strip and the channel are lined up (fig. A). Now, remove the paper from the strip’s adhesive backing (fig. B), and adhere the strip to the LED channel—starting at the lined end and working your way to the other end of the strip. Be sure to leave roughly 1/4-inch free at the end of the channel so that you can install the end cap as shown in figure C.

3. If one of your end caps doesn’t come with a pre-drilled hole, you will need to drill your own to allow the wires of the LED strip light to come through. In this case, we used a Dremel tool, but other options are viable as well. Regardless of the tool you choose, it is helpful to mark the end cap where you would like the wires to come through. Start the hole small, and increase the size as necessary.

4. Place the end cap on the wired side of the strip by threading the wires through the end cap as shown in figure A. Insert the end cap into the end of the light bar, and push firmly until it is fully in place (fig. B).

5. On the open end of the bar, slightly peel up the end of the LED strip (fig. A); this is necessary to install the end cap. Now measure your channel lens, and trim off the excess with clippers (fig. B). Be careful when trimming to avoid cracking the plastic. Excess material can be lightly sanded off. Once the lens has been cut to the proper length, slide it into the channel, and install the end cap as shown in figures C and D.

6. That’s it! Your customized LED light fixture is complete and ready for installation, which we will cover in the next step.

7. Mounting this LED profile is as easy as applying double-sided tape to the back of it and sticking it to your intended surface. Be sure to cut the tape to fit the back of the LED profile and to leave the tape backing on the side not attached to the channel until you are ready to mount it.

For most LED profiles, mounting clips are available for a more permanent installation.

If you have questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

Electrical jobs should never be turned into a DIY project, unless you have formal training and experience in the field. While electricity is extremely useful and necessary, if it isn’t handled correctly, it can be pretty dangerous too. If you get a novice to handle the job for you that can result in overloaded circuits, poor wiring connections or even faulty grounding, which can be extremely dangerous to you and your family and result in a fire outbreak as well. Here are some common services for which you would need to call in an electrician:

The main electrical panels provide electricity to your entire house. If you have older panels with fuses and older wiring, those may not be able to bear the load of any new appliances you decide to install on your property. The latest electrical appliances tend to add heavy loads on the system and your older wiring installations won’t be able to support those loads. If you are getting new appliances, call in a licensed electrician to test and inspect the wiring and circuit breakers on your property.

If you need any new outlets installed or need existing ones converted to USB ports, you would have to call in an electrician for the job. Oftentimes, electrical codes necessitate that a minimum of 1 outlet in your kitchen and bathroom be a GFCI outlet. These are specifically designed to shut off the power in case there is an imbalance in electricity or if water comes in contact with any of the electrical equipment or fittings; this helps in preventing shock in these areas.

It’s important that there be certified and licensed electrician should handle. They will take all the necessary precautions while doing any kind of electrical work on your property.