If you’re dying to install your new instructions for how to install a light bar. These instructions include options for installations with or without a wire harness and for connecting to existing LED lights. Installation will vary based on the type of vehicle, existing lighting setup, and chosen wiring method, but these instructions can serve to give you a general idea of the process. Light bar mounting instructions are also available and are listed by WH-DTS10, WWH-DTD30; (ATP) WH-ATPD20, sdoptional mounting brackets; be sure not to overtighten the hardware (you will need to adjust it in step 7).

3. Route the lighting side of the wiring harness from the battery to the light in a safe, secure manner. Connect the harness to the light. Be sure to avoid heat sources and any moving parts while running your wires. Prolonged chafing of the wires may lead to a short in the circuit. Typically, following the vehicle manufacturer’s wiring harness is a safe path to follow. Some lights may not have DT or ATP connections on them, but the connectors can be added from the harness kit or purchased separately (ATP-FPT).

4. Continue to route the switch portion of the harness to the desired location of the switch. The switch may need to be unplugged from the harness to make routing of the harness easier. An optional remote-controlled switch (RS-x) are also available with different legends.

5. Connect the black (ground) wire with the large ring terminal from the harness to the negative battery terminal. Connect the red (power) wire with the large ring terminal from the harness to the positive battery terminal.

6. Secure the relay to a suitable location, and test the light to make sure the circuit works.

7. Finally, aim the light in the desired direction, and tighten all mounting hardware.

3. Connect the black ground wire of the new light to the ground wire of the old light with solder and heat shrink tubing (PSC-x). Connect the red power wire of the new light to the power wire of the old light.

4. If the new LED work light or off-road light bar has an ATP or DT connector that you wish to utilize, corresponding ATP (DT-MPT) pigtails are available.

5. Finally, aim the lights in the proper direction, and tighten all mounting hardware.

1. Find a suitable mounting location that will allow for running wires and mounting the LED light bar. Mark where your holes will be for the light bar brackets or mounting feet. Check behind drilling locations to ensure nothing will be damaged. Drill appropriate-sized holes.

2. Mount the lights with the provided hardware or with DT-MPT or RRS-SP, RRS-SPx, or RCS-RF25A) under your hood to speed up install time and avoid routing wires through your vehicle’s firewall. Route another run of red wire from the pigtail adapter (connected to the light) to the output terminal of the switch. Be sure to avoid heat sources and any moving parts while running your wires. Prolonged chafing of the wires may lead to a short in the circuit. Typically, following the vehicle manufacturer’s wire harness is a safe path to follow.

4. Be sure to double-check for all obstructions and proper clearance. Drill an appropriate sized hole for the switch, and mount it.

5. Connect your black wire to the negative battery terminal. Connect your red wire to the switch input terminal and to the positive battery terminal with an appropriate-sized fuse holder (MAF-x) installed within 18 inches of the battery. You will have to cut your section of red wire to allow for the fuse holder to be installed between the switch and battery. Connect your other run of red wire to the switch output terminal.

6. Finally, aim the lights in the proper direction and tighten all mounting hardware.

We all want our families to be safe at home, and there are many products to help us feel safe. While some homeowners still use traditional deterrence methods like fences, bars, and “Beware of dog” signs, there are proactive and responsive electronic security systems being used today that can be much more effective. However, as with every electronic system, improper installation or malfunctions could make them a nuisance or even inoperable, leaving your home and family vulnerable.

Motion sensors seem to be especially problematic. When they are working improperly, they can add unnecessary costs to your electric bill and disrupt your sleep and peace of mind. But there is a lot that you can do before you call an electrician.

First, make sure you read the instructions carefully. Even if you’ve installed motion sensors before, you will need to take into account the specific specifications of the one you’re installing or troubleshooting. In addition, here are some tips that may solve the issue:

With spring upon us and summer just around the corner, you are probably itching to get the pool uncovered so you can host the first pool party of the season. Before you do that, you may want to consider upgrading, adding or replacing your existing pool lights. Pool lights add a certain quality to a pool while providing a layer of safety. However, there are several lights to choose from and you need to know which lights are best for your needs. An electrician in Beverly Hills has some tips for you to use when choosing your pool lights. If you have any other questions, you can call The Electric Connection.

There are two main options available for your pool lighting needs; in-ground and above ground. The above ground option is the cheapest. The in-ground tends to be a favorite simply because it provides a more uniform look.

Above Ground Options

Floating pool lights are inexpensive and do not require a Beverly Hills electrician to install. Simply pop the lights in the pool and it is done. The lights are festive, but they can interfere with swimming. You will also not have the benefit of the lights being stationary. It seems they tend to congregate and float to one area of the pool. For soft-sided pools, there are magnetic lights that stick to the side. These are again very easy to install and reliable. In Ground Options

LED bulbs are extremely bright and will last for around 10,000 hours. The lights are sealed in a waterproof housing. You can expect the bulbs to last anywhere from 10 to 15 years depending on how often the lights are used. Fiber optic lights are another option. However, they do tend to be much more expensive and the bulbs do not last nearly as long. In either case, you would need the pool lights installed by an electrician. Beverly Hills homeowners need to hire a professional to ensure the lights are installed safely and do not pose an electrical hazard. Give The Electric Connection a call today to schedule your pool light installation.