As you can see, no matter which type of scenario that lighting comes up in; it matters. Whether you run an office or a huge industrial sized factory; the quality of your lighting is highly important.

We are going to list the most important points that qualifies “good” industrial lighting systems, what to watch out for, as well as what to be on the look out for when it comes to your commercial lighting purchases.

Quality of light being produced. The quality of light that your lighting system will make or break your lighting system investment. If you cheap out initially and go with cheaper light sources such as HPS, you will regret it in the long run. Not only does LED typically offer a better CRI score, but it has many other benefits such as…

Do you want rebates for your lighting investment? If so; buy DLC qualified.

Conclusion

As we transition into Fall and Winter, there will be plenty of new outdoor activities for everyone to enjoy. It is important to remember that, there will also be new challenges associated with outdoor electrical safety. The piling of up leaves and falling of snow can create unpredictable electrical hazards around the home. Keeping safe while outdoors doesn’t have to be complicated. Practice proper electrical safety by following these 4 Expert Electric outdoor electrical safety tips:

It’s always a good idea to semi-annually audit your home’s outdoor electrical equipment, especially in between Winter and Spring and then again in Summer and Fall. This ensures that your home is fully prepared to take on any electrical hazards that could occur during severe weather and temperature fluctuations. A licensed electrician can can easily complete this audit for you; however, it’s also possible to undertake this task on your own if preferable. During this audit, ensure that all outdoor electrical equipment is not only functioning properly also stored properly.

Loose or damaged electrical wiring can pose a serious electrical threat to your home, especially if it comes into contact with snow or leaves. A thorough inspection of all wiring and electrical cords should be completed and followed up with a replacement if necessary.

Melting snow can often result in large amounts of water pooling on the ground. If this water comes into contact with electrical equipment and wiring, the equipment and entire home can be at risk. It’s best to plan ahead and ensure that all electrical equipment, wiring and cords are placed and stored so that they won’t come into contact with water sources.

When in doubt, it’s best to contact your local licensed electrician to ensure that your home or building is safe from outdoor electrical dangers. The team at Expert Electric can inspect all of your outdoor electrical equipment and appliances such as hot tubs and pools, ensuring that all of the necessary outdoor electrical safety requirements are met.

Have any questions about outdoor electrical safety or and of our electrical services? Please fill out one of the forms on our website. We are happy to answer any questions you may have. The Expert Electric team of licensed electricians is here to ensure all of your outdoor projects are handled safely. Call us today at 604-681-8338.

The home of the future has arrived! Home automation is now easier to find and more advanced than ever before. With home automation, various electrical and security components in your home are at your fingertips—even if you are on vacation several states away!

An application on your smartphone allows you to control the temperature, the garage door, your lights, some appliances, and even your locks. Find out how this can save you time and money below.

Has this ever happened to you? You’re running late for work, but as you’re pulling out of the driveway, you remember that you’ve forgotten to lock the doors. Or, you get all the way into the parking lot when you remember you left the garage door open.

These are both things you can monitor and correct using the home automation system’s application on your smartphone or tablet. As long as you have internet access, you can check on the locks, the garage door, and the lights to see if you forgot any of the basics. You will, however, need to install compatible home automation products for your home.

You’ve just arrived home from vacation, and you left the heat off or at a very low setting while you were away. When you walk into the door, you’re freezing! You have to run the heating system for a long time to feel comfortable again, and that’s certainly not the greeting you would like.

With home automation, you can adjust the thermostat from your smartphone. That way, when the plane lands, you can set the thermostat so that a warm home is waiting for you. And you can monitor energy usage while you’re gone to make sure the heater is working efficiently.

Finally, a home automation system helps you to monitor your energy usage throughout the day. You can find out when you use up the most energy, in order to make energy-smart choices about your lights and appliances.

Large foyer chandeliers and pendants make a true design statement, while providing plentiful illumination for the perfect introduction to your home or commercial space.

Your Guide to Finding the Perfect Foyer Chandelier

Whether you live in a cozy cottage or expansive mansion, fine lighting shines through more than any other home accessory or decorative piece.  A well-chosen foyer fixture creates a welcoming atmosphere, lending ambient illumination and decorative appeal to your home entryway.

1.  To achieve the desired effect, you need to size and install your foyer fixture properly.  A large foyer chandelier or decorative pendant fixture is especially enchanting if your home contains a defined foyer area with a raised ceiling or a glass picture window over the front door.

2.  To determine whether to use a semi-flush fixture, hanging pendant light or multi-tiered large foyer chandelier, you must know your ceiling height. The overall height of a foyer fixture should allow for a clearance of at least 7 feet from the floor.

3.  In a two-story foyer, if there is a window above the front door, center a larger foyer chandelier so that it may be seen from outside.

4.  If the foyer is extra-large, the addition of complementary wall sconces will supply additional illumination. Sconces should be installed 60 inches from the floor and at least 6 feet apart.

5.  Create a seamless flow by coordinating your large foyer chandelier with matching flush or semi-flush fixtures in hallways and powder rooms, or carry a unique design theme throughout by pairing an expansive foyer chandelier with a mini-chandelier in the powder room or extended archway.

The newest Corbett model, “Inertia” is a one-of-a-kind fixture, complete with polished stainless steel prisms and crystal.

This illuminating work of art by Jeff Andrews is prominently featured in the Kardashian’s “Dash” store in Los Angeles, California.   The “Inertia” fixture is provocative and stunning; with a 48-inch frame and eight lamps, this large foyer chandelier embodies a striking and sophisticated design.

The Kardashian family chose to feature the spectacular “Inertia” from Corbett Lighting to enhance the chic feel of the store and provide an eye-catching illumination for their clientele.

Maybe you’d like to put a little star power in your home entryway with a large foyer chandelier? Luxury lights and the latest decorative foyer chandeliers await customers at Capitol Lighting.   Receive one-on-one guidance with professional lighting experts who will help you find the perfect foyer fixture for your home or commercial space.

Find the exquisite “Inertia” series at Capitol Lighting stores or visit 1800lighting.com.  At Capitol, Corbett Lighting is a top-seller, and now with celebrity recognition.

relatively high ceilings. Drive by any industrial park, warehouse, or factory, and walk inside and what you will see is a high bay light.

But walk into any factory or warehouse and you will see different styles and options, wattage’s and configurations. Traditional high bay fixtures that were once common place were Mercury Vapor, which were then replaced with High Pressure Sodium and Metal Halide bulbs. As new technologies were introduced, and old technologies became more common, the old HID bulbs were replaced with Induction and Fluorescent light sources. And more recently with the more wide spread approval and popularity of LED, we started to see conversions from these older technologies to the latest energy saving LED High Bays.

A High Bay Fixture, depending on the light source, can take on many forms and shapes. If you consider a Metal Halide or High Pressure Sodium fixture, they typically consist of a large heat sink block at the top of the fixture that typically houses the fixtures ballast. Below is an aluminum or acrylic dome and at the top of the dome is the HID bulb. These bulbs typically come in two wattage’s, 400 and 1000. 400 Watt Fixtures tend to be installed in ceiling heights no higher than 30 feet, 1000 watt fixtures are typically 40 feet or higher. Interestingly enough, spacing of lights is similar to the height they are located off the floor. A fixture installed at 20 feet from the floor is installed in a 20X20 pattern, 30 feet in a 30X30 pattern, 40 feet in a 40X40 pattern. Of the 3 type of HID bulbs, Metal Halide tends to be the best option. High Pressure Sodium Bulbs are very low on the temperature color and have the warehouse aisles have the ability to focus the light where it is needed. A light designed for a warehouse aisle is a lot different than a light designed for a gymnasium or a factory floor. In these spaces, a light that can flood the area evenly is important, in a warehouse aisle, a light that can light up the face of the shelves and the floor below is important. And when selecting energy efficient options, its just as important to understand the technology and what it is capable of doing. Adding controls to a T5 fluorescent fixture is a good idea only if the ballast is designed to handle that requirement and not lower the life expectancy of the bulbs. Motions sensors and daylight controls that dim the light output based on occupants and the amount of daylight available in the space. Technologies such as metal halide and high pressure sodium are not a good choice as these technologies are not good at dimming or turn on or off quickly. Fluorescent can dim, but you need special ballasts for them. So knowing what you want to do and may want to do is important at time of purchase, because not having the proper equipment or options could mean a costly lighting warehouses, factories, gyms and readily available through the utility companies, and mass adoption means the technology of LED had matured to the point where the questions and disbelief of past years have gone away.